Security Certifications Compliance

The following topics describe how to configure your system to comply with security certifications standards:

Security Certifications Compliance Modes

Your organization might be required to use only equipment and software complying with security standards established by the U.S. Department of Defense and global certification organizations. Secure Firewall supports compliance with the following security certifications standards:

  • Common Criteria (CC): a global standard established by the international Common Criteria Recognition Arrangement, defining properties for security products

  • Unified Capabilities Approved Products List (UCAPL): a list of products meeting security requirements established by the U.S. Defense Information Systems Agency (DISA)


    Note
    The U.S. Government has changed the name of the Unified Capabilities Approved Products List (UCAPL) to the Department of Defense Information Network Approved Products List (DODIN APL). References to UCAPL in this documentation and the Secure Firewall Management Center web interface can be interpreted as references to DODIN APL.

  • Federal Information Processing Standards (FIPS) 140: a requirements specification for encryption modules

You can enable security certifications compliance in CC mode or UCAPL mode. Enabling security certifications compliance does not guarantee strict compliance with all requirements of the security mode selected. For more information on hardening procedures, refer to the guidelines for this product provided by the certifying entity.


Caution
After you enable this setting, you cannot disable it. If you need to take an appliance out of CC or UCAPL mode, you must reimage.

Security Certifications Compliance Characteristics

The following table describes behavior changes when you enable CC or UCAPL mode. (Restrictions on login accounts refers to command line access, not web interface access. )

System Change

Secure Firewall Management Center

Classic Managed Devices

Secure Firewall Threat Defense

CC Mode

UCAPL Mode

CC Mode

UCAPL Mode

CC Mode

UCAPL Mode

FIPS compliance is enabled.

Yes

Yes

Yes

Yes

Yes

Yes

The system does not allow remote storage for backups or reports.

Yes

Yes

—

—

—

—

The system starts an additional system audit daemon.

No

Yes

No

Yes

No

No

The system boot loader is secured.

No

Yes

No

Yes

No

No

The system applies additional security to login accounts.

No

Yes

No

Yes

No

No

The system disables the reboot key sequence Ctrl+Alt+Del.

No

Yes

No

Yes

No

No

The system enforces a maximum of ten simultaneous login sessions.

No

Yes

No

Yes

No

No

Passwords must be at least 15 characters long, and must consist of alphanumeric characters of mixed case and must include at least one numeric character.

No

Yes

No

Yes

No

No

The minimum required password length for the local admin user can be configured using the local device CLI.

No

No

No

No

Yes

Yes

Passwords cannot be a word that appears in a dictionary or include consecutive repeating characters.

No

Yes

No

Yes

No

No

The system locks out users other than admin after three failed login attempts in a row. In this case, the password must be reset by an administrator.

No

Yes

No

Yes

No

No

The system stores password history by default.

No

Yes

No

Yes

No

No

The admin user can be locked out after a maximum number of failed login attempts configurable through the web interface.

Yes

Yes

Yes

Yes

—

—

The admin user can be locked out after a maximum number of failed login attempts configurable through the local appliance CLI.

No

No

Yes, regardless of security certifications compliance enablement.

Yes, regardless of security certifications compliance enablement.

Yes

Yes

The system automtically rekeys an SSH session with an appliance:

  • After a key has been in use for one hour of session activity

  • After a key has been used to transmit 1 GB of data over the connection

Yes

Yes

Yes

Yes

Yes

Yes

The system performs a file system integrity check (FSIC) at boot-time. If the FSIC fails, Secure Firewall software does not start, remote SSH access is disabled, and you can access the appliance only via local console. If this happens, contact Cisco TAC.

Yes

Yes

Yes

Yes

Yes

Yes

Security Certifications Compliance Recommendations

Cisco recommends that you observe the following best practices when using a system with security certifications compliance enabled:

  • To enable security certifications compliance in your deployment, enable it first on the Secure Firewall Management Center, then enable it in the same mode on all managed devices.


    Caution
    The Secure Firewall Management Center will not receive event data from a managed device unless both are operating in the same security certifications compliance mode.

  • For all users, enable password strength checking and set the minimum password length to the value required by the certifying agency.

  • If you are using Secure Firewall Management Centers in a high-availability configuration, configure them both to use the same security certifications compliance mode.

  • When you configure Secure Firewall Threat Defense on a Firepower 4100/9300 to operate in CC or UCAPL mode, you should also configure the Firepower 4100/9300 to operate in CC mode. For more information, see the Cisco Firepower 4100/9300 FXOS Chassis Manager Configuration Guide.

  • Do not configure the system to use any of the following features:

    • Email reports, alerts, or data pruning notifications.

    • Nmap Scan, Cisco IOS Null Route, Set Attribute Value, or ISE EPS remediations.

    • Third-party client access to the system database.

    • External notifications or alerts transmitted via email (SMTP), SNMP trap, or syslog.

    • Audit log messages transmitted to an HTTP server or to a syslog server without using SSL certificates to secure the channel between the appliance and the server.

  • Do not enable external authentication using LDAP or RADIUS in deployments using CC mode.

  • Do not enable CACs in deployments using CC mode.

  • Disable access to the Secure Firewall Management Center and managed devices via the Secure Firewall REST API in deployments using CC or UCAPL mode.

  • Enable CACs in deployments using UCAPL mode.

  • Do not configure SSO in deployments using CC mode.

  • Do not configure Secure Firewall Threat Defense devices into a high availability pair unless they are both using the same security certifications compliance mode.


Note

The system does not support CC or UCAPL mode for:

  • Secure Firewall Threat Defense devices in clusters

  • Secure Firewall Threat Defense container instances on the Firepower 4100/9300

  • Exporting event data to an external client using eStreamer.

Appliance Hardening

For information about features you can use to further harden your system, see the latest versions of the Cisco Secure Firewall Management Center Hardening Guide and the Cisco Secure Firewall Threat Defense Hardening Guide, as well as the following topics within this document:

Protecting Your Network

See the following topics to learn about features you can configure to protect your network: