activate-ambr uplink bandwidth downlink bandwidth

Sets the aggregated maximum bit rate (AMBR) for the APN.

Configures uplink and downlink bandwidth. bandwidth must be an integer from 1 to 1000000000.

activate-flow-detection { initiation | termination } ruledef ruledef_name

Detects a flow and takes action.

initiation ruledef : Checks for flow initiation and adds a rule definition.

termination ruledef : Checks for flow termination and adds a rule definition.

ruledef_name must be an existing ruledef.

activate-lp-rule name lprule_name

Activates a local-policy rule within service scheme when a subscriber is in the configured RAI or TAI range.

lprule_name must be an existing local-policy rule within the service scheme expressed as an alphanumeric string of 1 through 63 characters.

Important

Local-Policy can support up to 7 lp-rules to be activated for a given session.

When the subscriber moves out of the configured RAI or TAI range, the local-policy rule is deactivated. This option is added as part of Location Based QoS Override feature. For more information on this feature, see the ECS Administration Guide.

activate-rule name rule_name

Activates a rule within ECS rulebase for a subscriber.

rule_name must be an existing rule within this local QoS policy service expressed as an alphanumeric string of 1 through 63 characters.

activate-rulebase name rulebase_name

Associates the session with a specific rulebase.

rulebase_name must be an existing rulebase within this local QoS policy service expressed as an alphanumeric string of 1 through 63 characters.

allow-requested-qos

Allow a specific UE initiated QoS request.

allow-session

Allows the session to continue.

deactivate-flow-detection { initiation | termination } ruledef ruledef_name

Deactivates detection of flow and takes action.

initiation ruledef : Checks for flow initiation and adds a rule definition.

termination ruledef : Checks for flow termination and adds a rule definition.

ruledef_name must be an existing ruledef.

deactivate-rule name rule_name

Deactivates a rule within ECS.

rule_name must be an existing rule within this local QoS policy service expressed as an alphanumeric string of 1 through 63 characters.

deactivate-rulebase name rulebase_name

Disassociates the rulebase from a session.

rulebase_name must be an existing rulebase within this local QoS policy service expressed as an alphanumeric string of 1 through 63 characters.

default-qos qci value arp value

Sets the default QoS parameters for the session

qci value must be an integer from 1 through 254.

arp value must be an integer from 1 through 15 (StarOS v12.1 and earlier) or 1 through 127 (StarOS v12.2 and later).

event-triggers { default-bearer-qos-change | ecgi-change | qos-change | tai-change | uli-change }

This action specifies to enable the event triggers – Default EPS bearer QoS change event trigger, ECGI-Change event trigger and QoS change event trigger.

The ECGI-Change event trigger is added as part of Location Based Local-Policy Rule Enforcement feature. For more information on this feature, see the Gx Interface Support chapter in the administration guide for the product you are deploying.

The TAI-Change and ULI-Change event triggers are added as part of Location Based QoS Override feature. For more information on this feature, see the ECS Administration Guide.

fetch-usage-from-up

This action specifies to fetch the usage report from UP by sending Sx-modify request to UP and uses that usage report values in the CCR-U.

reconnect-to-server [ send-usage-report ]

Reconnects to the PCRF server to handle fallback scenario. That is, when the session falls back to local policy, this action specifies to retry connecting to the PCRF server.

send-usage-report : Triggers CCR-U with volume report immediately. The default behavior is that the CCR-U will not be triggered immediately.

On timer-expiry, if the initial failure is due to CCR-U failure, and if send-ccru-immediate is configured, then CCR-U will be sent with the usage report immediately.

reject-requested-qos

Rejects UE QoS resource request.

retry-count value

Retry action. This applies to start-timer/activate-rule/activate-ruledef.

value must be an integer from 0 through 65535.

start-timer name duration value retry-count value

Starts a named timer. On expiry of this timer, the local policy engine is contacted to initiate the appropriate action, such as termination of a session.

duration value : Enter a timer duration from 0 through 28800 seconds. A value of 0 can be used to leave the local policy until the subscriber disconnects. Default timer value is 14400 (seconds).

retry-count specifies the maximum number of times the server will be retried before terminating the call.

retry-count value must be an integer from 0 through 65535. Default retry count is 3.

stop-timer name

Stops the designated timer.

terminate-session

Terminates the session.