- Preface
- 1 - Overview of Access Point Features
- 2 - Using the Web-Browser Interface
- 3 - Using the Command-Line Interface
- 4 - Configuring the Access Point for the First Time
- 5 - Administrating the Access Point
- 6 - Configuring Radio Settings
- 7 - Configuring Multiple SSIDs
- 8 - Configuring Spanning Tree Protocol
- 9 - Configuring an Access Point as a Local Authenticator
- 10 - Configuring WLAN Authentication and Encryption
- 11 - Configuring Authentication Types
- 12 - Configuring Other Services
- 13 - Configuring RADIUS and TACACS+ Servers
- 14 - Configuring VLANs
- 15 - Configuring QoS
- 16 - Configuring Filters
- 17 - Configuring CDP
- 18 - Configuring SNMP
- 19 - Configuring Repeater and Standby Access Points and Workgroup Bridge Mode
- 20 - Managing Firmware and Configurations
- 21 - Configuring L2TPv3 Over UDP/IP
- 22 - Configuring Ethernet over GRE
- 23 - Configuring System Message Logging
- 24 - Troubleshooting
- 25 - Miscellaneous AP-Specific Configurations
- Appendix A - Protocol Filters
- Appendix B - Supported MIBs
- Appendix C - Error and Event Messages
Supported MIBs
This appendix lists the Simple Network Management Protocol (SNMP) Management Information Bases (MIBs) that the access point supports for this software release. The Cisco IOS SNMP agent supports SNMPv1, SNMPv2, and SNMPv3.
MIB List
- IEEE802dot11-MIB
- Q-BRIDGE-MIB
- P-BRIDGE-MIB
- CISCO-DOT11-LBS-MIB
- CISCO-DOT11-IF-MIB
- CISCO-WLAN-VLAN-MIB
- CISCO-IETF-DOT11-QOS-MIB
- CISCO-IETF-DOT11-QOS-EXT-MIB
- CISCO-DOT11-ASSOCIATION-MIB
- CISCO-L2-DEV-MONITORING-MIB
- CISCO-DDP-IAPP-MIB
- CISCO-IP-PROTOCOL-FILTER-MIB
- CISCO-SYSLOG-EVENT-EXT-MIB
- CISCO-TBRIDGE-DEV-IF-MIB
- BRIDGE-MIB
- CISCO-CDP-MIB
- CISCO-CONFIG-COPY-MIB
- CISCO-CONFIG-MAN-MIB
- CISCO-FLASH-MIB
- CISCO-IMAGE-MIB
- CISCO-MEMORY-POOL-MIB
- CISCO-PROCESS-MIB
- CISCO-PRODUCTS-MIB
- CISCO-SMI-MIB
- CISCO-TC-MIB
- CISCO-SYSLOG-MIB
- CISCO-WDS-INFO-MIB
- ENTITY-MIB
- IF-MIB
- OLD-CISCO-CHASSIS-MIB
- OLD-CISCO-SYS-MIB
- OLD-CISCO-SYSTEM-MIB
- OLD-CISCO-TS-MIB
- RFC1213-MIB
- RFC1398-MIB
- SNMPv2-MIB
- SNMPv2-SMI
- SNMPv2-TC
Using FTP to Access the MIB Files
Follow these steps to obtain each MIB file by using FTP:
Step 1
Use FTP to access the server ftp.cisco.com.
Step 2 Log in with the username anonymous.
Step 3 Enter your e-mail username when prompted for the password.
Step 4 At the ftp> prompt, change directories to /pub/mibs/v1 or /pub/mibs/v2.
Step 5 Use the get MIB_filename command to obtain a copy of the MIB file.
Note You can also access information about MIBs on the Cisco web site:
http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
Feedback