Routing Command Reference for Cisco ASR 9000 Series Routers

address-family (EIGRP)

To enable an IPv4 address family under Enhanced Interior Gateway Routing Protocol (EIGRP), use the address-family command in the appropriate mode. To remove the address family from the EIGRP configuration, use the no form of this command.

address-family {ipv4 | ipv6}

no address-family {ipv4 | ipv6}

Syntax Description


ipv4	Selects IPv4 address family.

Command Default

No default behavior or values

Command Modes

Router configuration

VRF configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the address-family ipv4 command to configure IPv4 address family sessions in EIGRP.

EIGRP Virtual Private Networks (VPNs) can be configured under IPv4 address family configuration modes after first entering VRF configuration mode. All commands in address family configuration mode can be configured in VRF address families except the autonomous-system and maximum-prefix commands.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure an IPv4 VRF address family session after defining the VRF named vrf1:



  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# default-metric 1000 100 255 1 1500

Related Commands


Command	Description
autonomous-system	Configures an EIGRP routing process to run within a VRF.
maximum-prefix (EIGRP)	Limits the number of prefixes that are accepted under an address family by EIGRP.

authentication keychain

To authenticate all EIGRP protocol traffic on one or more interfaces based on the MD5 algorithm, use the authentication keychain command in an appropriate configuration mode. To disable authentication, use the no form of this command.

authentication keychain key-chain-name

no authentication keychain key-chain-name

Syntax Description


`key-chain-name`	Name of the authentication keychain

Command Default

Authentication is disabled.

Command Modes

IPv4 address family interface configuration

IPv6 address family interface configuration

IPv4 VRF address family interface configuration

IPv6 VRF address family interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the address-family ipv4 command to configure IPv4 address family sessions in EIGRP and the address-family ipv6 command to configure IPv6 address family sessions in EIGRP.

EIGRP Virtual Private Networks (VPNs) can be configured under IPv4 and IPv6 address family configuration modes after first entering VRF configuration mode.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to enable an EIGRP authentication keychain:


RP/0/RSP0/CPU0:router# configure eigrp 1
RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4 
RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/2/0/0 
RP/0/RSP0/CPU0:router(config-eigrp-if)# authentication key chain key1

Related Commands


Command	Description
router eigrp	Configures a routing process and enter router configuration mode for Enhanced Interior Gateway Routing Protocol (EIGRP).

auto-summary (EIGRP)

To allow automatic summarization of subnet routes into network-level routes for an Enhanced Interior Gateway Routing Protocol (EIGRP) process, use the auto-summary command in the appropriate configuration mode. To disable this function and send subprefix routing information across classful network boundaries, use the no form of this command.

auto-summary

no auto-summary

Syntax Description

This command has no keywords or arguments.

Command Default

The behavior of this command is disabled by default. (The software sends subnet routing information across classful network boundaries.)

Command Modes

IPv4 Address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Route summarization reduces the amount of routing information in the routing tables. Use the auto-summary command to allow the software to create summary subprefixes to the classful network boundary when crossing classful network boundaries.

EIGRP summary routes are given an administrative distance value of 5. You cannot configure this value.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to enable automatic summarization for EIGRP 1:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vpn-1
  
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# auto-summary

Related Commands


Command	Description
summary-address (EIGRP)	Configures a summary aggregate address for a specified interface.

autonomous-system

To configure an Enhanced Interior Gateway Routing Protocol (EIGRP) routing process to run within a VPN routing and forwarding instance (VRF), use the autonomous-system command in IPv4 VRF address family configuration mode.

autonomous-system as-number

no autonomous-system as-number

Syntax Description


`as-number`	Autonomous system number of the EIGRP routing process. Range is from 1 to 65535.

Command Default

None

Command Modes

IPv4 VRF address family configuration.

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the autonomous-system command in IPv4 VRF address family configuration mode.

Task ID


Task ID	Operations
eigrp	read, write

Examples

This example shows how to configure autonomous system 101 under VRF VPN-1:


RP/0/RSP0/CPU0:router(config)# router eigrp 1
 RP/0/RSP0/CPU0:router(config-eigrp)# vrf vpn-1
RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# autonomous-system 101

Related Commands


Command	Description
vrf (EIGRP)	Defines a VRF instance and to enters VRF configuration mode.

bandwidth-percent (EIGRP)

To configure the percentage of bandwidth that may be used by EIGRP on an interface, use the bandwidth-percent command in interface configuration mode. To restore the default value, use the no form of this command.

bandwidth-percent percent

no bandwidth-percent

Syntax Description


percent	Percentage of bandwidth that EIGRP may use.

Command Default

percent : 50

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

EIGRP uses up to 50 percent of the bandwidth of a link, as defined by the bandwidth interface configuration command. This command may be used if some other fraction of the bandwidth is desired. Values greater than 100 percent may be configured. The configuration option may be useful if the bandwidth is set artificially low for other reasons.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure EIGRP to use up to 75 percent (42 kbps) of an interface in autonomous system 209:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# router-id 10.1.1.1
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/0
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# bandwidth-percent 75

Related Commands


Command	Description
bandwidth (interface)	Sets a bandwidth value for an interface.

bfd fast-detect (EIGRP)

To enable Bidirectional Forwarding Detection (BFD) to detect failures in the path between adjacent forwarding engines, use the bfd fast-detect command in router configuration mode. To return the software to the default state in which BFD is not enabled, use the no form of this command.

bfd fast-detect

no bfd fast-detect

Syntax Description

This command has no keywords or arguments.

Command Default

BFD detection of failures in the path between adjacent forwarding engines is disabled.

Command Modes

Router configuration

Command History


Release	Modification
Release 5.2.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure BFD on a EIGRP router:


RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# router eigrp 100
RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-af)# interface gigabitEthernet 2/2/2/1
RP/0/RSP0/CPU0:router(config-eigrp-af-if)# bfd fast-detect

bfd minimum-interval (EIGRP)

To specify the minimum control packet interval for BFD sessions for the corresponding BFD configuration scope, use the bfd minimum-interval command in router configuration mode. To return the router to the default setting, use the no form of this command.

bfd minimum-interval milliseconds

no bfd minimum-interval [milliseconds]

Syntax Description


`milliseconds`	Interval between sending BFD hello packets to the neighbor. The range is 15 to 30000 milliseconds.

Command Default

EIGRP interval : 50 milliseconds

Command Modes

Router configuration

Command History


Release	Modification
Release 5.2.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure BFD minimum interval on a EIGRP router:


RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# router eigrp 100
RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-af)# interface gigabitEthernet 2/2/2/1
RP/0/RSP0/CPU0:router(config-eigrp-af-if)# bfd minimum-interval 50

Related Commands

Command	Description
address-family ipv4 unicast (BFD)	Enables BFD fast-detection on a specific IPV4 unicast destination address prefix and on the forwarding next-hop address.
bfd minimum-interval	Specifies the minimum control packet interval for BFD sessions for the corresponding BFD configuration scope.
bfd multiplier	Sets the BFD multiplier.
show bfd	Displays BFD information for a specific location.

bfd multiplier (EIGRP)

To set the Bidirectional Forwarding Detection (BFD) multiplier, use the bfd multiplier command in the appropriate configuration mode. To return the router to the default setting, use the no form of this command.

bfd multiplier multiplier

no bfd multiplier [multiplier]

Syntax Description


`multiplier`	Number of times a packet is missed before BFD declares the neighbor down. The range is 2 to 50.

Command Default

The default multiplier is 3.

Command Modes

Router configuration

Command History


Release	Modification
Release 5.2.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure BFD minimum interval on a EIGRP router:


RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# router eigrp 100
RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-af)# interface gigabitEthernet 2/2/2/1
RP/0/RSP0/CPU0:router(config-eigrp-af-if)# bfd multiplier 5

clear eigrp neighbors

To remove and re-establish Enhanced Interior Gateway Routing Protocol (EIGRP) neighbor entries from the appropriate table, use the clear eigrp neighbors command in EXEC configuration mode.

clear eigrp [as-number] [vrf {vrf | | all}] [ipv4 | | ipv6] neighbors [ip-address| type interface-path-id] [soft]

Syntax Description


`as-number`	(Optional) Autonomous system number. Range is from 1 to 65535.
vrf { `vrf` \| all }	(Optional) Specifies a particular VPN routing and forwarding instance (VRF) or all VRF instances.
ipv4	(Optional) Specifies the IPv4 address family.
`ip-address`	(Optional) Address of the neighbor.
`type`	Interface type. For more information, use the question mark ( ? ) online help function.
`interface-path-id`	Physical interface or virtual interface. Use the show interfaces command to see a list of all interfaces currently configured on the router. For more information about the syntax for the router, use the question mark ( ? ) online help function.
soft	(Optional) Specifies a soft reset.

Command Default

When no autonomous system number or VRF instance is specified, all EIGRP neighbor entries are cleared from the table.

Command Modes

EXEC configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to clear all EIGRP VRF entries for neighbor Gigabit Ethernet interface 0/5/0/0:



RP/0/RSP0/CPU0:router# clear eigrp customer_1 neighbors GigabitEthernet 0/5/0/0

Related Commands


Command	Description
show eigrp interfaces	Displays information about interfaces configured for EIGRP.
show eigrp neighbors	Displays the neighbors discovered by EIGRP.

clear eigrp topology

To remove and relearn Enhanced Interior Gateway Routing Protocol (EIGRP) topology entries from the appropriate table, use the clear eigrp topology command in EXEC configuration mode.

clear eigrp [as-number] [vrf {vrf | | all}] [ipv4 | | ipv6] topology [prefix mask | | prefixl/ength]

Syntax Description


as-number	(Optional) Autonomous system number. Range is from 1 to 65535.
vrf { `vrf` \| all }	(Optional) Specifies a particular VPN routing and forwarding instance (VRF) or all VRF instances.
ipv4	(Optional) Specifies the IPv4 address family.
prefix	IP prefix, which limits output to a specific route.
mask	IP address mask.
`/` `length`	Prefix length, which can be indicated as a slash (/) and number. For example, /8 indicates that the first eight bits in the IP prefix are network bits. If `length` is used, the slash is required.

Command Default

No EIGRP topology entries are cleared.

Command Modes

EXEC configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to clear EIGRP topology entries for a specific route:


RP/0/RSP0/CPU0:router# clear eigrp topology 10.1.0.0/8

Related Commands


Command	Description
show eigrp topology	Displays information for the EIGRP topology table.

default-information

To control the candidate default routing information for an Enhanced Interior Gateway Routing Protocol (EIGRP), use the defaultinformation command in the appropriate configuration mode. To suppress EIGRP candidate default information in incoming or outgoing updates, use the no form of this command.

default-information allowed {in | out} [route-policy name]

no default-information allowed {in | out} [route-policy name]

Syntax Description


allowed	Specifies EIGRP to allow default routing information.
in	Specifies EIGRP to allow inbound default routing information.
out	Specifies EIGRP to allow outbound default routing information.
route-policy `name`	(Optional) Specifies a route policy.

Command Default

Default routing information is not accepted or flagged.

Command Modes

Address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure inbound default routes specified with route policy acme to be accepted by an EIGRP peer in autonomous system 1:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# default-information accept in route-policy acme

default-metric (EIGRP)

To set metrics for an Enhanced Interior Gateway Routing Protocol (EIGRP), use the defaultmetric command in the appropriate configuration mode. To remove the metric values and restore the default state, use the no form of this command.

default-metric bandwidth delay reliability loading mtu

no default-metric

Syntax Description


`bandwidth`	Minimum bandwidth of the route in kilobits per second. Range is 1 to 4294967295.
`delay`	Route delay in ten microsecond units. Range is 1 to 4294967295.
`reliability`	Likelihood of successful packet transmission expressed as a number between 0 and 255. The value 255 means 100-percent reliability; 0 means the link is not reliable.
`loading`	Effective bandwidth of the route expressed as a number from 1 to 255 (255 is 100-percent loading).
`mtu`	Minimum maximum transmission unit (MTU) size of the route in bytes. Range is from 1 to 65535.

Command Default

No default values

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the default-metric command to provide default metric values while redistributing a protocol into EIGRP.

Metric defaults have been carefully set to work for a wide variety of networks. Take great care when changing these values.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to take redistributed Routing Information Protocol (RIP) metrics and translate them into EIGRP metrics with values as follows: bandwidth = 1000, delay = 100, reliability = 250, loading = 100, and MTU = 1500.


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# redistribute rip
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# default-metric 1000 100 250 100 1500

Related Commands


Command	Description
redistribute	Redistributes routes from one routing domain into another routing domain.

distance (EIGRP)

To allow the use of one of two administrative distances—internal and external—that could provide a better route to a node, use the distance command in the appropriate configuration mode. To reset these values to their defaults, use the no form of this command.

distance internal-distance external-distance

no distance

Syntax Description


`internal-distance`	Administrative distance for EIGRP internal routes. Internal routes are those that are learned from another entity within the same autonomous system (AS). The distance can be a value from 1 to 255.
`external-distance`	Administrative distance for EIGRP external routes. External routes are those for which the best path is learned from a source external to the AS. The distance can be a value from 1 to 255.

Command Default

internal-distance : 90

external-distance : 170

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

An administrative distance is a rating of the trustworthiness of a routing information source, such as an individual router or a group of routers. Numerically, an administrative distance is an integer from 0 to 255. In general, the higher the value, the lower the trust rating. An administrative distance of 255 means the routing information source cannot be trusted at all and should be ignored.

Use the distance command if another protocol is known to provide a better route to a node than was actually learned through the external Enhanced Interior Gateway Routing Protocol (EIGRP) or some internal routes should be preferred by EIGRP.

To display the default administrative distance for a specified routing process, use the show protocols EXEC command.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to set the administrative distance of all EIGRP 1 internal routes (within vrf vpn-1) to 80 and all EIGRP external routes to 130:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# distance 80 130

Related Commands


Command	Description
show protocols (EIGRP)	Displays information about the Enhanced Interior Gateway Routing Protocol (EIGRP) running on the router.

hello-interval (EIGRP)

To configure the hello interval for an interface, use the hello-interval command in interface configuration mode. To restore the default value, use the no form of this command.

hello-interval seconds

no hello-interval

Syntax Description


`seconds`	Hello interval (in seconds). Range is from 1 to 65535.

Command Default

For low-speed, nonbroadcast multiaccess (NBMA) networks: 60 seconds

For all other networks: 5 seconds

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to set the hello interval to 10 seconds for the interface:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp)# router-id 10.1.1.1
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/0
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# hello-interval 10

hold-time (EIGRP)

To configure the hold time for an interface, use the hold-time command in interface configuration mode. To restore the default value, use the no form of this command.

hold-time seconds

no hold-time

Syntax Description


`seconds`	Hold time (in seconds). Range is from 1 to 65535.

Command Default

Three times the default hello interval time of 15 seconds.

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

On very congested and large networks, the default hold time might not be sufficient time for all routers to receive hello packets from their neighbors. In this case, you may want to increase the hold time.

We recommend that the hold time be at least three times the hello interval. If a router does not receive a hello packet within the specified hold time, routes through this router are considered unavailable.

Increasing the hold time delays route convergence across the network.

To ensure nonstop forwarding during RP failovers, we recommend that the hold time be increased to 30 seconds.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to set the hold time to 0 to 40 seconds for the interface:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp)# router-id 10.1.1.1
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/0
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# hold-time 40

Related Commands


Command	Description
bandwidth (interface)	Sets a bandwidth value for an interface.
hello-interval (EIGRP)	Configures the hello interval for the EIGRP routing process designated by an autonomous system number.

interface (EIGRP)

To define the interfaces on which the Enhanced Interior Gateway Routing Protocol (EIGRP) routing protocol runs, use the interface command in the appropriate configuration mode. To disable EIGRP routing for interfaces, use the no form of this command.

interface type interface-path-id

no interface type interface-path-id

Syntax Description

type

Interface type. For more information, use the question mark ( ? ) online help function.

interface-path-id

Physical interface or virtual interface.

Note

Use the show interfaces command to see a list of all interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark ( ? ) online help function.

Command Default

When you do not specify this command in configuration mode, EIGRP routing for interfaces is not enabled.

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the interface command to associate a specific interface with an EIGRP process. The interface remains associated with the process even when the IPv4 address of the interface changes.

This command places the router in interface configuration mode, from which you can configure interface-specific settings. Commands configured under this mode (such as the hello-interval command) are automatically bound to that interface.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to enter interface configuration mode for EIGRP process 1 and set the hello interval to 10 seconds for GigabitEthernet interface 0/1/0/0:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp)# router-id 10.1.1.1
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/0
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# hello-interval 10

log-neighbor-changes

To enable the logging of changes in Enhanced Interior Gateway Routing Protocol (EIGRP) neighbor adjacencies, use the log-neighbor-changes command in the appropriate configuration mode. To disable the logging of changes in EIGRP neighbor adjacencies, use the no form of this command.

log-neighbor-changes

no log-neighbor-changes

Command Default

This command has no keywords or arguments.

Adjacency changes are not logged.

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the log-neighbor-changes command to log neighbor adjacency changes, monitor the stability of the routing system, and help detect problems. Logging is disabled by default. To disable the logging of neighbor adjacency changes, use the no form of this command.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to enable logging of neighbor changes for EIGRP 1:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# log-neighbor-changes

log-neighbor-warnings

To enable the logging of Enhanced Interior Gateway Routing Protocol (EIGRP) neighbor warning messages, use the log-neighbor-warnings command in the appropriate configuration mode. To disable the logging of EIGRP neighbor warning messages, use the no form of this command.

log-neighbor-warnings

no log-neighbor-warnings

Syntax Description

This command has no keywords or arguments.

Command Default

Neighbor warning messages are not logged.

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the log-neighbor-warnings command to disable and enable neighbor warning messages. When neighbor warning messages occur, they are not logged by default.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure log neighbor warning messages for EIGRP process 20:


  RP/0/RSP0/CPU0:router(config)# router eigrp 20
  RP/0/RSP0/CPU0:router(config-eigrp) vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# log-neighbor-warnings

maximum-paths (EIGRP)

To control the maximum number of parallel routes that the Enhanced Interior Gateway Routing Protocol (EIGRP) can support, use the maximum-paths command in the appropriate configuration mode. To remove the maximum-paths command from the configuration file and restore the system to its default condition with respect to the routing protocol, use the no form of this command.

maximum-paths maximum

no maximum-paths

Syntax Description


`maximum`	Maximum number of parallel routes that EIGRP can install in a routing table. Range is from 1 to 32 routes .

Command Default

maximum : 4

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the maximum-paths command to allow the EIGRP protocol to install multiple paths into the routing table for each prefix. Multiple paths are installed for both internal and external routes, providing these routes are learned in the same autonomous system and that they are equal cost (according to the EIGRP best path algorithm).

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to allow a maximum of 10 paths to a destination:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# maximum-paths 10

maximum-prefix (EIGRP)

To limit the number of prefixes that are accepted under a VRF address family by Enhanced Interior Gateway Routing Protocol (EIGRP), use the maximum-prefix command in IPv4 VRF address family configuration mode. To disable this function, use the no form of this command.

maximum-prefix maximum [threshold] [dampened] [reset-time minutes] [restart minutes] [restart-count number] [warning-only]

no maximum-prefix maximum [threshold] [dampened] [reset-time minutes] [restart minutes] [restart-count number] [warning-only]

Syntax Description

maximum

Maximum number of prefixes allowed under an address family. Range is from 1 to 4294967295.

The number of prefixes that can be configured is limited only by the available system resources on the router.

threshold

(Optional) Syslog warning messages are specified as a percentage of the maximum prefix limit that was exceeded. The prefix percentage number range is from 1 to 100. The default is 75 percent.

dampened

(Optional) A decay penalty is applied to the restart time period each time the maximum prefix limit is exceeded. The half-life for the decay penalty is 150 percent of the default or user-defined restart time value in minutes. This keyword is disabled by default.

reset-time minutes

(Optional) The restart count is reset to 0 after the default or user-defined reset time period has expired. The range of values that can be applied with the minutes argument is from 1 to 65535 minutes. The default reset-time period is 15 minutes.

restart minutes

(Optional) A time period when router adjacencies are not formed or when redistributed routes are not accepted from the RIB after the maximum prefix limit has been exceeded. The value for the minutes argument is from 1 to 65535 minutes. The default restart time period is 5 minutes.

restart-count number

(Optional) Number of times a peering session is automatically reestablished after the peering session is torn down or after the redistribute route is cleared and relearned when the maximum prefix exceeds limits. The default restart count limit is 3.

Caution

After the restart count threshold is crossed, you need to use the clear eigrp neighbors command to re-establish normal peering, redistribution, or both.

warning-only

(Optional) Configures the router to generate syslog messages only when the maximum prefix limit is reached, instead of terminating the peering session.

Command Default

threshold: 75 percent

dampened : False

reset-time : 15 minutes

restart : 5 minutes

restart-count : 3

warning-only : False

Command Modes

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the maximum-prefix command to limit the number of prefixes that are accepted from all sources. When the maximum prefix limit is exceeded, sessions with remote peers are torn down, all routes learned from remote peers and through redistribution are removed from the topology and routing tables, and redistribution and peering are suspended for the default or user-defined time period.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure the maximum prefix limit for an EIGRP process, which includes routes learned through redistribution and routes learned through EIGRP peering sessions. The maximum limit is set to 50,000 prefixes. When the number of prefixes learned through redistribution reaches 37,500 (75 percent of 50,000), warning messages are displayed in the console. When the maximum prefix limit is exceeded, all peering sessions are reset, the topology and routing tables are cleared and redistributed routes and all peering sessions are placed in a penalty state.


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# maximum-prefix 50000

Related Commands


Command	Description
clear eigrp neighbors	Deletes EIGRP VPN neighbor entries from the table.
clear route	Deletes routes from the IP routing table.

metric (EIGRP)

To set metrics for an Enhanced Interior Gateway Routing Protocol (EIGRP) interface, use the metric command in interface configuration mode. To remove the metric values and restore the default state, use the no form of this command.

metric {bandwidth | delay | load | reliability}

no metric

Syntax Description


bandwidth	Minimum interface bandwidth of the route in kilobits per second. Range is 1 to 4294967295.
delay	Interface route delay in tens of microseconds. Delay is 1 or any positive number that is a multiple of 39.1 nanoseconds. Range is 1 to 4294967295.
load	Effective bandwidth of the route expressed as a number from 1 to 255 (255 is 100-percent loaded).
reliability	Likelihood of successful packet transmission expressed as a number between 0 and 255. The value 255 means 100-percent reliability; 0 means no reliability.

Command Default

Metric values are not set.

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.6.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the metric command to provide metric values while redistributing a protocol into an EIGRP interface. Metric defaults have been carefully set to work for a wide variety of networks. Take great care when changing these values.

Task ID


Task ID	Operation
eigrp	read, write

Examples

This example shows how to configure metric values for interface POS 0/1/0/1 with values as bandwidth = 100, delay = 7, reliability = 250, and load = 100.


RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# router eigrp 100
RP/0/RSP0/CPU0:router(config-eigrp)# address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/1
RP/0/RSP0/CPU0:router(config-eigrp-af-if)# metric bandwidth 100 delay 7 reliability 250 load 100

Related Commands


Command	Description
default-metric (EIGRP)	Sets metrics for an Enhanced Interior Gateway Routing Protocol (EIGRP).

metric maximum-hops

To advertise as unreachable those Enhanced Interior Gateway Routing Protocol (EIGRP) routes with a hop count higher than is specified by the command, use the metric maximum-hops command in the appropriate configuration mode. To reset the value to the default, use the no form of this command.

metric maximum-hops hops-number

no metric maximum-hops

Syntax Description


hops-number	Maximum hop count. Range is from 1 to 255 hops.

Command Default

hops-number : 100

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the metric maximum-hops command to provide a safety mechanism that breaks any potential count-to-infinity problems. This command causes the EIGRP routing protocol to advertise as unreachable routes with a hop count greater than the value assigned to the hops-number argument.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure a hop count to 200 for a router that has a complex WAN generating a large hop count under normal (nonlooping) operations.


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# metric maximum-hops 200

Related Commands


Command	Description
metric weights	Allows the tuning of the EIGRP metric calculations.

metric rib-scale

To set a RIB scale for EIGRP, use the metric rib-scale command in an appropriate configuration mode. To remove the RIB scale and restore the default state, use the no form of this command.

metric rib-scale scale-down-value

no metric rib-scale

Syntax Description


`scale-down-value`	Amount to divide the EIGRP Wide Metric by to convert to a 4 Byte RIB metric. Legal ranges are 1-256. Results are expressed as whole integers only (no rounding).

Command Default

Default RIB scale is 128 in the 64 bit mode.

In 32 bit mode, rib scale is always 1.

Command Modes

IPv4 address family configuration

IPv6 address family configuration

IPv4 VRF address family configuration

IPv6 VRF address family configuration (Only supported in 64 bit mode)

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The ability to scale the RIB metric is provided through the use of the metric rib-scale configuration command. When entered, the command will result in all routes in the RIB being cleared and replaced with the new metric values.

Task ID


Task ID	Operation
eigrp	read, write

Examples

This example shows how to set the metric rib-scale as 64:


Router#configure
Router(config)#router eigrp 1
Router(config-eigrp)#address-family ipv4
Router(config-eigrp-af)#metric rib-scale 64

metric weights

To allow the tuning of the Enhanced Interior Gateway Routing Protocol (EIGRP) metric calculations, use the metric weights command in the appropriate configuration mode. To reset the values to their defaults, use the no form of this command.

metric weights tos k1 k2 k3 k4 k5

no metric weights

Syntax Description


`tos`	Type of service (ToS) which must always be 0.
`k1 k2 k3 k4 k5`	Constants that convert an EIGRP metric vector into a scalar quantity. The range is 0 to 4294967295.

Command Default

tos: 0

k1: 1

k2: 0

k3: 1

k4: 0

k5: 0

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the metric weights command to alter the default behavior of EIGRP routing and metric computation and allow the tuning of the EIGRP metric calculation for a particular ToS.

If k5 equals 0, the composite EIGRP metric is computed according to the following formula:

metric = [k1 * bandwidth + (k2 * bandwidth)/(256 – load) + k3 * delay]

If k5 does not equal zero, an additional operation is performed:

metric = metric * [k5/(reliability + k4)]

Bandwidth is inverse minimum bandwidth of the path in BPS scaled by a factor of 2.56 * 1012. The range is from a 1200-bps line to 10 terabits per second.

Delay is in units of 10 microseconds. The range of delay is from 10 microseconds to 168 seconds. A delay of all 1s indicates that the network is unreachable.

The delay parameter is stored in a 32-bit field, in increments of 39.1 nanoseconds. The range of delay is from 1 (39.1 nanoseconds) to hexadecimal FFFFFFFF (decimal 4,294,967,040 nanoseconds). A delay of all 1s (that is, a delay of hexadecimal FFFFFFFF) indicates that the network is unreachable.

This table lists the default values used for several common media.

Table 1. Bandwidth Values by Media Type
Media Type	Delay	Bandwidth
Satellite	5120 (2 seconds)	5120 (500 megabits)
Ethernet	25600 (1 milliseconds [ms])	256000 (10 megabits)
1.544 Mbps	512000 (20,000 ms)	1,657,856 bits
64 kbps	512000 (20,000 ms)	40,000,000 bits
56 kbps	512000 (20,000 ms)	45,714,176 bits
10 kbps	512000 (20,000 ms)	256,000,000 bits
1 kbps	512000 (20,000 ms)	2,560,000,000 bits

Reliability is given as a fraction of 255. That is, 255 is a reliability of 100 percent or a perfectly stable link. Load is given as a fraction of 255. A load of 255 indicates a completely saturated link.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to set the metric weights to change the default values:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# metric weights 0 2 0 2 0 0

Related Commands


Command	Description
metric maximum-hops	Advertises as unreachable those EIGRP VPN routes with a hop count higher than is specified by the command.

neighbor (EIGRP)

To define a neighboring router with which to exchange Enhanced Interior Gateway Routing Protocol (EIGRP) information, use the neighbor command in interface configuration mode. To remove an entry, use the no form of this command.

neighbor ip-address interface [remote [max-hops] ]

no neighbor ip-address interface [remote [max-hops] ]

Syntax Description


`ip-address`	IP address of a peer router with which routing information is exchanged.
`interface`	Interface through which peering is established.
remote	Specifies that the neighbor is remote.
`max-hops`	The maximum number of hops within which the neighbor is expected to be reachable from the configured router. The default value is 100 hops.

Command Default

No neighboring routers are defined.

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the neighbor command to permit the point-to-point (nonbroadcast) exchange of routing information.

If a neighbor is configured on an interface using the neighbor command, the interface stops sending or receiving multicast hello messages. However, the interface can send or receive unicast hello messages. So each neighbor on a LAN must be configured individually .Multiple neighbor commands can be used to specify additional neighbors or peers.

Task ID


Task ID	Operations
eigrp	read, write

Examples

This example shows how to permit the sending of EIGRP updates to specific neighbors. One copy of the update is generated for each neighbor:


  RP/0/RSP0/CPU0:router(config)# router eigrp 100
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/0/0/3
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# neighbor 172.20.1.2 remote 10

Related Commands


Command	Description
passive-interface (EIGRP)	Disables sending and receiving "hello" messages on (EIGRP) interface.

neighbor maximum-prefix

To limit the number of prefixes that are accepted from a single Enhanced Interior Gateway Routing Protocol (EIGRP) neighbor or all EIGRP VPN neighbors, use the neighbor maximum-prefix command in IPv4 VRF address family configuration mode. To disable this function, use the no form of this command.

Single-Neighbor Configuration CLI

neighbor ip-address maximum-prefix maximum [threshold] [warning-only]

no neighbor ip-address maximum-prefix

All-Neighbor Configuration CLI

neighbor maximum-prefix maximum [threshold] [dampened] [reset-time minutes] [restart minutes] [restart-count number] [warning-only]

no neighbor maximum-prefix

Syntax Description

ip-address

(Optional) IP address of a single peer.

maximum

Maximum number of prefixes accepted. The range is from 1 to 4294967295.

The number of prefixes that can be configured is limited only by the available system resources on the router.

threshold

(Optional) Syslog warning messages are specified as a percentage of the maximum prefix limit that was exceeded. The prefix percentage number range is from 1 to 100. The default is 75 percent.

dampened

(Optional) Configures a decay penalty to be applied to the restart time period each time the maximum prefix limit is exceeded. The half-life for the decay penalty is 150 percent of the default or user-defined restart time value in minutes. This keyword is disabled by default.

reset-time minutes

(Optional) Configures the router to reset the restart count to 0 after the default or configured reset time period has expired. The range is from 1 to 65535 minutes.

restart minutes

(Optional) Configures a time period in which the router does not form adjacencies or accept redistributed routes from the RIB after the maximum prefix limit has been exceeded. The range is from 1 to 65535 minutes.

restart-count number

(Optional) Configures the number of times a peering session can be automatically reestablished after the peering session has been torn down or a redistribute route has been cleared and relearned because the maximum prefix limit has been exceeded.

Caution

After the restart count threshold is crossed, you need to use the clear eigrp neighbors command to reestablish normal peering, redistribution, or both.

warning-only

(Optional) Configures the router to generate syslog messages only when the maximum prefix limit is reached, instead of terminating the peering session.

Command Default

threshold: 75 percent

dampened : disabled

warning-only : disabled

reset-time : 15 minutes

restart : 5 minutes

restart-count : 3

Command Modes

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The neighbor maximum-prefix command is configured to protect an individual peering session or all peering sessions. When this feature is enabled and the maximum prefix limit is exceeded, the router tears down the peering session, clears all routes that are learned from the peer, and then places the peer in a penalty state for the default or user-defined time period. After the penalty time period expires, normal peering is reestablished.

Note

In EIGRP, neighbor commands have been used traditionally to configure static neighbors. In the context of this feature, however, the neighbor maximum-prefix command can be used to configure the maximum prefix limit for both statically configured and dynamically discovered neighbors.

When configuring the neighbor maximum-prefix command to protect a single peering session, just the maximum prefix limit, percentage threshold, and warning only configuration options can be configured. Session dampening, restart, and reset timers are configured on a global basis.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure the maximum prefix limit for a single peer. The maximum limit is set to 1000 prefixes, and the warning threshold is set to 80 percent. When the maximum prefix limit is exceeded, the session with this peer is torn down, all routes learned from this peer are removed from the topology and routing tables, and this peer is placed in a penalty state for 5 minutes (default penalty value).


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# neighbor 10.0.0.1 maximum-prefix 1000 80

The following example shows how to configure the maximum prefix limit for all peers. The maximum limit is set to 10,000 prefixes, the warning threshold is set to 90 percent, the restart timer is set to 4 minutes, a decay penalty is configured for the restart timer with the dampened keyword, and all timers are configured to be reset to 0 every 60 minutes. When the maximum prefix limit is exceeded, all peering sessions are torn down, all routes learned from all peers are removed from the topology and routing tables, and all peers are placed in a penalty state for 4 minutes (user-defined penalty value). A dampening exponential decay penalty is also applied.


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vrf1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# neighbor maximum-prefix 10000 90 dampened reset-time 60 restart4

Related Commands


Command	Description
clear eigrp neighbors	Deletes EIGRP and VRF neighbor entries from the appropriate tables.

next-hop-self disable

To instruct the Enhanced Interior Gateway Routing Protocol (EIGRP) process to use the received next-hop value when advertising the routes, use the next-hop-self disable command in interface configuration mode. To revert to the default, use the no form of this command.

next-hop-self disable

no next-hop-self disable

Syntax Description

This command has no keywords or arguments.

Command Default

EIGRP always sets the IP next-hop value to be itself.

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

EIGRP, by default, sets the IP next-hop value to be itself for routes that it is advertising, even when advertising those routes on the same interface from which learned them. To change this default, you must use the next-hop-self disable interface configuration command to instruct EIGRP to use the received next-hop value when advertising these routes.

The next-hop-self disable feature is not available for redistributed routes.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to change the default IP next-hop value and instruct EIGRP to use the received next-hop value:


RP/0/RSP0/CPU0:router(config)# router eigrp 1
RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/0
RP/0/RSP0/CPU0:router(config-eigrp-af-if)# next-hop-self disable

nsf disable (EIGRP)

To disable Enhanced Interior Gateway Routing Protocol (EIGRP) nonstop forwarding (NSF), use the nsf disable command in appropriate configuration mode. To re-enable the EIGRP NSF from a disabled state, use the no form of this command.

nsf disable

no nsf disable

Syntax Description

This command has no keywords or arguments.

Command Default

NSF in EIGRP is enabled.

Command Modes

Router Configration

IPv4 address family configuration

IPv6 address family configuration

IPv4 VRF address family configuration

IPv6 VRF address family configuration

Command History


Release	Modification
Release 4.1.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If NSF is to be disabled for both IPv4 and IPv6 address families of all VRFs, use the nsf disable command at router configuration mode.

If NSF is to be disabled for a specific address family under a specific VRF, use the nsf disable command at address family configuration mode.

If NSF is disabled, EIGRP will not be able to retain the routes learnt from its peers and may result in traffic loss during ISSU.

Task ID


Task ID	Operation
eigrp	read, write

Examples

This example shows how to disable NSF for all address families under all VRF's:


RP/0/RSP0/CPU0:router#configure
RP/0/RSP0/CPU0:router(config)#router eigrp 1
RP/0/RSP0/CPU0:router(config-eigrp)#nsf disable

This example shows how to disable NSF for IPv4 address family of VRF v1:


RP/0/RSP0/CPU0:router#configure
RP/0/RSP0/CPU0:router(config)#router eigrp 1
RP/0/RSP0/CPU0:router(config-eigrp)#vrf v1
RP/0/RSP0/CPU0:router(config-eigrp-vrf)#address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)#nsf disable

Related Commands


Command	Description
router eigrp	Configures a routing process and enters router configuration mode for Enhanced Interior Gateway Routing Protocol (EIGRP).

passive-interface (EIGRP)

To disable sending and receiving "hello" messages on an Enhanced Interior Gateway Routing Protocol (EIGRP) interface and to disable formation of neighbors on the interface, use the passive-interface command in interface configuration mode. To reenable sending and receiving "hello messages", use the no form of this command.

passive-interface

no passive-interface

Syntax Description

This command has no keywords or arguments.

Command Default

passive-interface command is disabled on an interface.

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the passive-interface command to disable sending of "hello" massages. The particular subnet on that interface will continue to be advertised by EIGRP to neighbors on other interfaces.

Task ID


Task ID	Operations
eigrp	read, write

Examples

This example shows how to configure passive-interface command on GigabitEthernet interface 0/6/5/0:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv6
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/6/5/0
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# passive-interface

redistribute (EIGRP)

To inject routes from one routing domain into the Enhanced Interior Gateway Routing Protocol (EIGRP), use the redistribute command in the appropriate configuration mode. To remove the redistribute command from the configuration file and restore the system to its default condition in which the software does not redistribute routes, use the no form of this command.

redistribute {{bgp | connected | isis | ospf | rip | static | eigrp} | [as-number | instance-name]} [ route-policy name]

no redistribute

Syntax Description


bgp	Distributes routes from the BGP protocol.
connected	Distributes routes that are established automatically by virtue of having enabled IP on an interface.
isis	Distributes routes from the IS-IS protocol.
ospf	Distributes routes from the OSPF protocol. This protocol is supported in the IPv4 address family.
static	Redistributes IP static routes.
`as-number \| instance-name`	Represents one of the following three options: For the bgp keyword: Range for 2-byte Autonomous system numbers (ASNs) is 1 to 65535. Range for 4-byte Autonomous system numbers (ASNs) in asplain format is 1 to 4294967295. Range for 4-byte Autonomous system numbers (ASNs) is asdot format is 1.0 to 65535.65535. For the isis keyword, an IS-IS instance name from which routes are to be redistributed. The value takes the form of a string. A decimal number can be entered, but it is stored internally as a string. For the ospf keyword, an OSPF instance name from which routes are to be redistributed. The value takes the form of a string. A decimal number can be entered, but it is stored internally as a string.
route-policy `name`	(Optional) Specifies the identifier of a configured policy. A policy is used to filter the importation of routes from this source routing protocol to EIGRP.

Command Default

Route redistribution is disabled.

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.
Release 3.9.0	Asplain format for 4-byte Autonomous system numbers notation was supported.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Redistributed routing information should always be filtered by the route- policy name keyword and argument. This filtering ensures that only those routes intended by the administrator are redistributed by EIGRP.

A default metric is usually required to redistribute routes from another protocol into EIGRP. The metric is configured through the default-metric command or under the route policy configured with the redistribute command. The one exception to this requirement is when EIGRP redistributes BGP routes on a provider edge (PE) router in an MPLS-VPN scenario. If the originating protocol of the route is EIGRP with the same autonomous system (as in MPLS-VPN), the metric would be learned automatically from the extended communities of the BGP route.

For information about routing policies, see the Routing Policy Commands on Cisco ASR 9000 Series Router module of the Cisco ASR 9000 Series Aggregation Services Router Routing Command Reference.

Task ID


Task ID	Operations
eigrp	read, write

Examples

This example shows how to cause BGP routes to be redistributed into an EIGRP autonomous system:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# redistribute bgp 100

This example shows how to redistribute the specified IS-IS process routes into an EIGRP autonomous system within a VPN routing and forwarding instance (VRF). The IS-IS routes are redistributed using route policy 3.


  RP/0/RSP0/CPU0:router(config)# router eigrp 109
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vpn-1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# redistribute isis 108 route-policy 3

Related Commands


Command	Description
default-metric (EIGRP)	Sets metrics for an EIGRP.

redistribute maximum-prefix

To limit the number of prefixes redistributed into an Enhanced Interior Gateway Routing Protocol (EIGRP) process, use the redistribute maximum-prefix command in IPv4 VRF address family configuration mode. To disable this function, use the no form of this command.

redistribute maximum-prefix maximum [threshold] [ [dampened] [reset-time minutes] [restart minutes] [restart-count number] | [warning-only]]

no redistribute maximum-prefix

Syntax Description


maximum	Maximum number of prefixes that are redistributed into EIGRP under an address-family. The range is from 1 to 4294967295. The number of prefixes that can be configured is limited only by the available system resources on the router.
threshold	(Optional) Syslog warning messages are specified as a percentage of the maximum prefix limit that was exceeded. The prefix percentage number range is from 1 to 100. The default is 75 percent.
restart `minutes`	(Optional) Configures a time period in which the router will not form adjacencies or accept redistributed routes from the RIB after the maximum-prefix limit has been exceeded. The value for the minutes argument is from 1 to 65535 minutes.
restart-count `number`	(Optional) Configures the number of times a peering session can be automatically reestablished after the peering session has been torn down or after the redistribute route has been cleared and relearned because the maximum prefix limit has been exceeded. After the restart count threshold has been crossed, you will need to enter the process restart eigrp command to reestablish normal peering, redistribution, or both.
reset-time `minutes`	(Optional) Configures the router to reset the restart count to 0 after the default or configured reset time period has expired. The value for the minutes argument is from 1 to 65535 minutes.
dampened	(Optional) Configures a decay penalty to be applied to the restart time period each time the maximum prefix limit is exceeded. The half-life for the decay penalty is 150 percent of the default or user-defined restart time value in minutes.
warning-only	(Optional) Configures the router to only generate syslog messages when the maximum prefix limit is reached, instead of suspending redistribution.

Command Default

threshold: 75 percent

warning-only : disabled

reset-time : 15 minutes

restart : 5 minutes

restart-count : 3

dampened: disabled

Command Modes

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the redistribute maximum-prefix command to configure limit prefixes learned through redistribution. When the maximum prefix limit is exceeded, all routes learned from the Routing Information Base (RIB) are discarded and redistribution is suspended for the default or user-defined time period. The maximum prefix limit that can be configured for redistributed prefixes is limited only by the available system resources on the router.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure the maximum prefix limit for routes learned through redistribution. The maximum limit is set to 5000 prefixes, and the warning threshold is set to 95 percent. When the number of prefixes learned through redistribution reaches 4750 (95 percent of 5000), warning messages are displayed in the console. Because the warning-only keyword is configured, the topology and routing tables are not cleared and route redistribution is not placed in a penalty state.


  RP/0/RSP0/CPU0:router(config)# router eigrp 100
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vpn-1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# redistribute maximum-prefix 5000 95 warning-only

Related Commands


Command	Description
process	To start, terminate, or restart a process.

remote-neighbor (unicast)

To configure any neighbor that is multiple hops away, including remote static neighbors, use the remote-neighbor command.

remote-neighbors unicast-listen [allow-list route-policyname] [max-neighbors maxRemotePeers]

no remote-neighbors unicast-listen [allow-list route-policyname] [max-neighbors maxRemotePeers]

Syntax Description


unicast-listen	Use unicast to form remote neighbor relationship without having to manually configure the remote neighbors addresses.
allow-list `route policy name`	Name of the route-policy that specifies remote addresses from which EIGRP neighbor connections may be accepted.
max-neighbors `maximum remote peers`	The maximum number of remote neighbors from which connection can be accepted. The range is 1-65535.

Command Modes

Router configuration

Command History


Release	Modification
Release 5.2.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the remote-neighbor unicast-listen command to configure a neighbor to use unicast to communicate with a neighbor that is multiple hops away, and whose address has not been configured with the neighbor command. A single unicast address can only be configured to a single remote static neighbor for a given address-family. If you try to configure a second remote static neighbor using the same unicast address but a different interface, it is rejected. EIGRP configuration of remote neighbors under different address families is unrestricted.

Task ID


Task ID	Operation
eigrp	read, write

Examples

This example shows you how to configure both devices (hub and spoke) involved in the neighbor relationship.

RP/0/RSP0/CPU0:HUB(config)#router eigrp 100
RP/0/RSP0/CPU0:HUB(config-eigrp)#address-family ipv4
RP/0/RSP0/CPU0:HUB(config-eigrp-af)#int g0/0/0/3
RP/0/RSP0/CPU0:HUB(config-eigrp-af-if)#exit
RP/0/RSP0/CPU0:HUB(config-eigrp-af)#interface gigabitEthernet 0/0/0/3
RP/0/RSP0/CPU0:HUB(config-eigrp-af-if)#remote-neighbor unicast-listen
RP/0/RSP0/CPU0:HUB(config-eigrp-af-if)#commit

RP/0/RSP0/CPU0:spoke(config)#router eigrp 100
RP/0/RSP0/CPU0:spoke(config-eigrp)#address-family ipv4
RP/0/RSP0/CPU0:spoke(config-eigrp-af)#interface g0/0/0/3
RP/0/RSP0/CPU0:spoke(config-eigrp-af-if)#neighbor 21.21.21.1
RP/0/RSP0/CPU0:spoke(config-eigrp-af-if)#commit

RP/0/RSP0/CPU0:spoke#sh run router eigrp
Fri Aug  8 08:47:48.556 UTC
router eigrp 100 
address-family ipv4  
interface GigabitEthernet0/0/0/3   
neighbor 21.21.21.1  !!!

route-policy (EIGRP)

To apply a routing policy to updates advertised to or received from an Enhanced Interior Gateway Routing Protocol (EIGRP) neighbor, use the route-policy command in the appropriate configuration mode. To disable applying routing policy to updates, use the no form of this command.

route-policy route-policy-name {in | out}

no route-policy route-policy-name {in | out}

Syntax Description


`route-policy-name`	Name of route policy.
in	Applies policy to inbound routes.
out	Applies policy to outbound routes.

Command Default

No policy is applied.

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the route-policy command to specify a routing policy for an inbound or outbound route. The policy can be used to filter routes or modify route attributes.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to apply the IN-Ipv4 policy to inbound IP Version 4 (IPv4) routes:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# route-policy IN-IPv4 in

router eigrp

To configure a routing process and enter router configuration mode for Enhanced Interior Gateway Routing Protocol (EIGRP), use the router eigrp command in global configuration mode. To turn off the EIGRP routing process, use the no form of this command.

router eigrp {instance-autonomous-system-number| virtual-instance-name}

no router eigrp {instance-autonomous-system-number| virtual-instance-name}

Syntax Description


`instance-autonomous-system-number`	EIGRP instance autonomous-system number. This is used as the autonomous-system number for the default/global VRF. Valid range is 1 to 65535.

Command Default

No routing process is defined.

Command Modes

Global configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Only one instance of EIGRP is supported.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example configures EIGRP routing process 109 (109 is the autonomous-system number of default/global VRF):


  RP/0/RSP0/CPU0:router(config)# router eigrp 109
  RP/0/RSP0/CPU0:router(config-eigrp)#

router-id (EIGRP)

To configure a router ID for an Enhanced Interior Gateway Routing Protocol (EIGRP) process, use the router-id command in the appropriate configuration mode. To cause the software to use the default method of determining the router ID, use the no form of this command.

router-id router-id

no router-id

Syntax Description


`router-id`	32-bit router ID value specified in four-part, dotted-decimal notation.

Command Default

If this command is not configured, EIGRP chooses an IPv4 address as the router ID from one of its interfaces.

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

It is good practice to use the router-id command to explicitly specify a unique 32-bit numeric value for the router ID. This action ensures that EIGRP can function regardless of the interface address configuration.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to assign the IP address of 172.20.1.1 to the EIGRP process 1:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# router-id 172.20.1.1

show eigrp accounting

To display prefix accounting information for Enhanced Interior Gateway Routing Protocol (EIGRP) processes, use the show eigrp accounting command in EXEC mode.

show eigrp [as-number] [vrf {vrf-name | all}] [ipv4 | | ipv6] accounting

Syntax Description


`as-number`	(Optional) Autonomous system number. This option is available when a VPN routing and forwarding (VRF) instance is not specified. Range is from 1 to 65535.
vrf { `vrf-name` \| all }	(Optional) Specifies a particular VPN routing and forwarding instance (VRF) or all VRF instances.
[ ipv4 ]	(Optional) Specifies the IPv4 address family.

Command Default

This command has no arguments or keywords.

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
EIGRP	read

Examples

The following is sample output from the show eigrp accounting command:


  RP/0/RSP0/CPU0:router# show eigrp accounting
  
  IP-EIGRP accounting for AS(100)/ID(10.0.2.1) Routing Table: RED
  Total Prefix Count: 4  States: A-Adjacency, P-Pending, D-Down
  
  State Address/Source   Interface        Prefix   Restart  Restart/
                                          Count     Count   Reset(s)
   P    Redistributed     ----               0           3         211
   A    10.0.1.2          Gi0/6/0/0/         2           0          84
   P    10.0.2.4          Gi00/2/0/3         0           2         114
   D    10.0.1.3          Gi0/6/0/0          0           3           0

Note

Connected and summary routes are not listed individually in the output of this command but are counted in the total aggregate count for each process.

This table describes the significant fields shown in the display.

Table 2. show eigrp accounting Field Descriptions

Field

Description

EIGRP accounting for AS

Identifies the EIGRP instance along with the AS number, router ID and table ID.

Total Prefix Count

Shows the aggregate sum of the prefixes in an EIGRP instance topology table. The count includes prefixes learned from all neighbors or from redistribution.

States: A-Adjacency, P-Pending, D-Down

A-Adjacency: Indicates a stable adjacency with the neighbor or a normal redistribution state.

P-Pending: Neighbor adjacency or redistribution is suspended or in a penalized state because the maximum prefix limit was exceeded.

D-Down: Neighbor adjacency or redistribution is suspended permanently until a manual reset is performed with the clear route command.

Address/Source

Shows the peer IP address of the redistribution source.

Prefix Count

Displays the total number of learned prefixes by source.

Note

Routes can be learned for the same prefix from multiple sources, and the sum of all prefix counts in this column may be greater than the figure displayed in the “Prefix Count” field.

Restart Count

Number of times a route source exceeded the maximum prefix limit.

Restart Reset(s)

Displays the time, in seconds, that a route source is in a P (penalized) state. If the route source is in an A (stable or normal) state, the displayed time, in seconds, is the time period until penalization history is reset.

show eigrp interfaces

To display information about interfaces configured for Enhanced Interior Gateway Routing Protocol (EIGRP), use the show eigrp interfaces command in EXEC mode.

show eigrp [as-number] [vrf {vrf-name | | all}] [ipv4 | ipv6] interfaces [type interface-path-id] [detail]

Syntax Description


as-number	(Optional) Autonomous system number. This option is available when a VPN routing and forwarding (VRF) instance is not specified. Range for 2-byte Autonomous system numbers (ASNs) is 1 to 65535. Range for 4-byte Autonomous system numbers (ASNs) in asplain format is 1 to 4294967295. Range for 4-byte Autonomous system numbers (ASNs) is asdot format is 1.0 to 65535.65535.
vrf { `vrf-name` \| all }	(Optional) Specifies a particular VPN routing and forwarding instance (VRF) or all VRF instances.
[ ipv4 ]	(Optional) Specifies the IPv4 address family.
type	(Optional) Interface type. For more information, use the question mark ( ? ) online help function.
interface-path-id	Physical interface or virtual interface. Use the show interfaces command to see a list of all interfaces currently configured on the router. For more information about the syntax for the router, use the question mark ( ? ) online help function.
detail	(Optional) Displays detailed EIGRP interface information.

Command Default

This command has no arguments or keywords.

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.2	This command was introduced.
Release 3.9.0	As plain format for 4-byte Autonomous system numbers notation was supported. The input parameters and output were modified to display 4-byte autonomous system numbers and extended communities in either asplain or asdot notations.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show eigrp interfaces command to determine on which interfaces EIGRP is active and learn information about EIGRP related to those interfaces.

If an interface is specified, only that interface is displayed. Otherwise, all interfaces on which EIGRP is running are displayed.

If an autonomous system is specified, only the routing process for the specified autonomous system is displayed. Otherwise, all EIGRP processes are displayed.

Task ID


Task ID	Operations
EIGRP	read

Examples

The following is sample output from the show eigrp interfaces command:


  RP/0/RSP0/CPU0:router# show eigrp interfaces
  
  IP EIGRP interfaces for process 1
  
                           Xmit Queue    Mean   Pacing Time   Multicast   Pending
  Interface        Peers   Un/Reliable   SRTT   Un/Reliable   Flow Timer  Routes
  
  Gi0/6/0/2.212      0         0/0          0      11/434          0          0
  
  Gi0/6/0/0          1         0/0        337       0/10           0          0
  
   Gi0/2/0/3         1         0/0         10       1/63         103          0
  
  Gi0/6/2/5          1         0/0        330       0/16           0          0

This table describes the significant fields shown in the display.

Table 3. show eigrp interfaces Field Descriptions
Field	Description
Interface	Interface over which EIGRP is configured.
Peers	Number of directly connected EIGRP neighbors.
Xmit Queue Un/Reliable	Number of packets remaining in the unreliable and reliable transmit queues.
Mean SRTT	Mean smoothed round-trip time (SRTT) internal (in milliseconds).
Pacing Time Un/Reliable	Pacing time used to determine when EIGRP packets should be sent out the interface (unreliable and reliable packets).
Multicast Flow Timer	Maximum number of seconds in which the router sends multicast EIGRP packets.
Pending Routes	Number of routes in the packets in the transmit queue waiting to be sent.

The following is sample output from the show eigrp interfaces command when issued with the detail keyword:


  RP/0/RSP0/CPU0:router# show eigrp interfaces detail
  
  IPv4-EIGRP interfaces for AS(100)
  
                          Xmit Queue   Mean   Pacing Time   Multicast    Pending
  Interface        Peers  Un/Reliable  SRTT   Un/Reliable   Flow Timer   Routes
  Lo0                0        0/0         0     640/640          0           0
    Hello interval is 5 sec, hold time is 15 sec
    Next xmit serial <none>
    Un/reliable mcasts: 0/0  Un/reliable ucasts: 0/0
    Mcast exceptions: 0  CR packets: 0  ACKs suppressed: 0
    Retransmissions sent: 0  Out-of-sequence rcvd: 0
    Bandwidth percent is 50
    Total packets received: 0
    Authentication mode: MD5  Key chain: key1
    No active key found in keychain database
    Valid authenticated packets received: 0
    Packets dropped due to wrong keychain config: 0
    Packets dropped due to missing authentication: 0
    Packets dropped due to invalid authentication: 0
    Effective Metric:
      Bandwidth: 10000000, Delay: 500, Reliability: 255, Load: 1, MTU: 1514

This table describes the significant fields shown in the display.

Table 4. show eigrp interfaces detail Field Descriptions
Field	Description
Hello interval	Hello packet transmission interval.
hold time	Hold time announced to neighbors. If neighbors do not get hello packets from the router for this period, neighbors declare that the neighbor relationship is down.
Next xmit serial	Next transmission serial number.
Un/reliable mcasts	Number of unreliable and reliable multicast packets sent on this interface.
Un/reliable ucasts	Number or unreliable and reliable unicast packets sent on this interface.
Mcast exceptions	Number of multicast exceptions (sequence TLVs).
CR packets	Number of packets sent with the conditional receive bit set.
ACKs suppresses	Number of ACK packets suppressed.
Retransmissions	Number of retransmissions sent on this interface.
Out-of-sequence rcvd	Number of packets received out of sequence.
Bandwidth percent	Configured percent of bandwidth.
Authentication	Mode of authentication.
Valid authenticated packets received	Number of valid authentication packets.
Packets dropped due to wrong keychain config	Number of packets dropped due to wrong keychain configuration.
Packets dropped due to missing authentication	Number of packets dropped due to missing authentication.
Packets dropped due to invalid authentication	Number of packets dropped due to invalid authentication.

Related Commands


Command	Description
show eigrp neighbors	Displays the neighbors discovered by EIGRP.

show eigrp neighbors

To display information about neighbors discovered by Enhanced Interior Gateway Routing Protocol (EIGRP), use the show eigrp neighbors command in EXEC mode.

show eigrp as-numbervrf {vrf-name | all}ipv4ipv6

Syntax Description


`as-number`	(Optional) Autonomous system number. This option is available when a VPN routing and forwarding (VRF) instance is not specified. Range is from 1 to 65535.
vrf { `vrf-name` \| all }	(Optional) Specifies a particular VPN routing and forwarding instance (VRF) or all VRF instances.
[ ipv4 ]	(Optional) Specifies the IPv4 address family.
detail	(Optional) Displays detailed EIGRP neighbor information.
type	Interface type. For more information, use the question mark ( ? ) online help function.
`interface-path-id`	Physical interface or virtual interface. Use the show interfaces command to see a list of all interfaces currently configured on the router. For more information about the syntax for the router, use the question mark ( ? ) online help function.
static	(Optional) Displays static routes.

Command Default

No default behavior or values

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show eigrp neighbors command to determine when neighbors become active and inactive. This command is also useful for debugging certain types of transport problems.

Task ID


Task ID	Operations
EIGRP	read

Examples

The following is sample output from the show eigrp neighbors command:


  RP/0/RSP0/CPU0:router# show eigrp neighbors
  
  IP-EIGRP Neighbors for process 77
  
  Address                 Interface     Holdtime Uptime   Q      Seq  SRTT  RTO
                                        (secs)   (h:m:s)  Count  Num  (ms)  (ms)
  
  172.16.81.28             Gi0/2/0/3     13       0:00:41  0      11   4     20
  
  172.16.80.28            Gi0/6/0/0      14       0:02:01  0      10   12    24
  
  172.16.80.31            Gi0/6/2/5      12       0:02:02  0      4    5     20 
  
  RP/0/RSP0/CPU0:router#

This table describes the significant fields shown in the display.

Table 5. show eigrp neighbors Field Descriptions
Field	Description
process	Autonomous system number specified in the router configuration command.
Address	IP address of the EIGRP peer.
Interface	Interface on which the router is receiving hello packets from the peer.
Holdtime	Length of time (in seconds) that the Cisco IOS XR software waits to hear from the peer before declaring that the peer is down.
Uptime	Elapsed time (in hours, minutes, and seconds) since the local router first heard from this neighbor.
Q Count	Number of EIGRP packets (update, query, and reply) that the software waits to send.
Seq Num	Sequence number of the last update, query, or reply packet that was received from this neighbor.
SRTT	Smoothed round-trip time. This is the number of milliseconds required for an EIGRP packet to be sent to this neighbor and for the local router to receive an acknowledgment of that packet.
RTO	Retransmission timeout (in milliseconds). This is the amount of time the software waits before resending a packet from the retransmission queue to a neighbor.

The following is sample output from the show eigrp neighbors command when issued with the detail keyword:


  RP/0/RSP0/CPU0:router# show eigrp neighbors detail 
  
  IP-EIGRP neighbors for AS 1
  
  H   Address                 Interface       Hold Uptime   SRTT   RTO  Q  Seq
                                              (sec)         (ms)       Cnt Num
  0   11.0.0.10               Gi0/6/0/0         14 01:00:52    3   200  0  10
  
     Version 12.4/1.2, Retrans: 0, Retries: 0, Prefixes: 3

This table describes the significant fields shown in the display.

Table 6. show eigrp neighbors detail Field Descriptions
Field	Description
Version	Version of EIGRP software (major.minor) running on the node and neighbor.
Retrans	Number of retransmissions sent to this neighbor.
Retries	Number of retransmissions sent to this neighbor since the last acknowledgement (ACK).
Prefixes	Number of prefixes learned from this neighbor.

show eigrp topology

To display the Enhanced Interior Gateway Routing Protocol (EIGRP) topology table, use the show eigrp topology command in EXEC mode.

show eigrp [as-number] [vrf {vrf-name | | all}] [ipv4 | | ipv6] topology [ip-address mask] {active | | all-links | | detail-links | | pending | | summary | | zero-successors}

Syntax Description


`as-number`	(Optional) Autonomous system number. This option is available when a VPN routing and forwarding (VRF) instance is not specified. Range for 2-byte Autonomous system numbers (ASNs) is 1 to 65535. Range for 4-byte Autonomous system numbers (ASNs) in asplain format is 1 to 4294967295. Range for 4-byte Autonomous system numbers (ASNs) is asdot format is 1.0 to 65535.65535.
vrf { `vrf-name` \| all }	(Optional) Specifies a particular VPN routing and forwarding instance (VRF) or all VRF instances.
[ ipv4 ]	(Optional) Specifies the IPv4 address family.
`ip-address`	(Optional) IP address in four-part, dotted-decimal notation.
`mask`	(Optional) Network mask specified in either of two ways: Network mask can be a four-part, dotted decimal address. For example, 255.0.0.0 indicates that each bit equal to 1 means the corresponding address bit is a network address. Network mask can be indicated as a slash (/) and number. For example, /8 indicates that the first 8 bits of the mask are 1s, and the corresponding bits of the address are the network address.
active	(Optional) Displays only active entries in the EIGRP topology table.
all-links	(Optional) Displays all entries in the EIGRP topology table.
detail-links	(Optional) Displays detailed information for all entries in the EIGRP topology table.
pending	(Optional) Displays all entries in the EIGRP topology table that are waiting for an update from a neighbor or are waiting to reply to a neighbor.
summary	(Optional) Displays a summary of the EIGRP topology table.
zero-successors	(Optional) Displays available routes in the EIGRP topology table.

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.2	This command was introduced.
Release 3.9.0	Asplain format for 4-byte Autonomous system numbers notation was supported. The input parameters and output were modified to display 4-byte autonomous system numbers and extended communities in either asplain or asdot notations.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

When the show eigrp topology command is used without any keywords or arguments, only routes that are feasible successors are displayed.

The show eigrp topology command can be used to determine Diffusing Update Algorithm (DUAL) states and to debug possible DUAL problems.

Task ID


Task ID	Operations
EIGRP	read

Examples

The following is sample output from the show eigrp topology command. The EIGRP metrics for specified internal routes and external routes are displayed.


  RP/0/RSP0/CPU0:router# show eigrp topology 10.2.1.0/24
  
  IP-EIGRP (AS 1): Topology entry for 10.2.1.0/24
    State is Passive, Query origin flag is 1, 1 Successor(s), FD is 281600
    Routing Descriptor Blocks:
    0.0.0.0 (GigabitEthernet0/6/0/0), from Connected, Send flag is 0x0
      Composite metric is (281600/0), Route is Internal !This is the internal route.
      Vector metric:
        Minimum bandwidth is 10000 Kbit
        Total delay is 1000 microseconds
        Reliability is 255/255
        Load is 1/255 
        Minimum MTU is 1500
        Hop count is 0
  
  RP/0/RSP0/CPU0:router# show eigrp topology 10.4.80.0/20
  
  IP-EIGRP (AS 1): Topology entry for 10.4.80.0/20
    State is Passive, Query origin flag is 1, 1 Successor(s), FD is 409600
    Routing Descriptor Blocks:
    10.2.1.1 (GigabitEthernet0/6/0/0), from 10.2.1.1, Send flag is 0x0
      Composite metric is (409600/128256), Route is External
      Vector metric:
        Minimum bandwidth is 10000 Kbit
        Total delay is 6000 microseconds
        Reliability is 255/255
        Load is 1/255
        Minimum MTU is 1500
        Hop count is 1
      External data:
        Originating router is 10.89.245.1 
        AS number of route is 0
        External protocol is Connected, external metric is 0
        Administrator tag is 0 (0x00000000)

This table describes the significant fields shown in the display.

Table 7. show eigrp topology Field Descriptions
Field	Description
Query origin	Query origin state.
Successors	Number of feasible successors for this prefix.
FD	Feasible distance for this prefix.
10.2.1.1 (Gi0/0)	Next hop and interface from which this path was learned.
from 10.2.1.1	Information source for this path.
Send flag	Indicates if the sending of this prefix is pending to this neighbor.
Composite Metric (409600/128256)	The first number is the EIGRP metric that represents the cost to the destination. The second number is the EIGRP metric that this peer advertised.
Route is	Type of route (internal or external).
Vector Metric	Shows the metric (bandwidth, delay, reliability, load, MTU, and hop count) advertised by the neighbor.
External Data	Shows the external information (originating router ID, AS number, external protocol, metric, and tag) advertised by the neighbor.

show eigrp traffic

To display the number of Enhanced Interior Gateway Routing Protocol (EIGRP) packets sent and received, use the show eigrp traffic command in EXEC mode.

show eigrp [as-number] [vrf {vrf-name | | all}] [ipv4 | | ipv6] traffic

Syntax Description


`as-number`	(Optional) Autonomous system number. This option is available when a VPN routing and forwarding (VRF) instance is not specified. Range is from 1 to 65535.
vrf { `vrf-name` \| all }	(Optional) Specifies a particular VPN routing and forwarding instance (VRF) or all VRF instances.
[ ipv4 ]	(Optional) Specifies the IPv4 address family.

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show eigrp traffic command to find the number of packets sent and received.

In addition, this command is useful in determining whether packets from one node are not reaching the neighboring node due to connectivity or configuration problems.

Task ID


Task ID	Operations
EIGRP	read

Examples

The following is sample output from the show eigrp traffic command:


  RP/0/RSP0/CPU0:router# show eigrp traffic
  
  IP-EIGRP Traffic Statistics for AS 1
  
    Hellos sent/received: 736/797
    Updates sent/received: 6/6
    Queries sent/received: 0/1
    Replies sent/received: 1/0
    Acks sent/received: 6/6
    Input queue high water mark 0, 0 drops
    SIA-Queries sent/received: 0/0
    SIA-Replies sent/received: 0/0

This table describes the significant fields shown in the display.

Table 8. show eigrp traffic Field Descriptions
Field	Description
AS	Autonomous system number specified in the router eigrp command.
Hellos sent/received	Number of hello packets sent and received.
Updates sent/received	Number of update packets sent and received.
Queries sent/received	Number of query packets sent and received.
Replies sent/received	Number of reply packets sent and received.
Acks sent/received	Number of acknowledgment packets sent and received.
Input queue high water mark	Maximum number of packets in the input queue and number of drops.
SIA-Queries sent/received	Number of Stuck-in-Active query packets sent and received.
SIA-Replies sent/received	Number of Stuck-in-Active reply packets sent and received.

show protocols (EIGRP)

To display information about the Enhanced Interior Gateway Routing Protocol (EIGRP) process configuration, use the show protocols command in EXEC mode.

show protocols [ipv4 | | | afi-all] [all | | protocol] [default-context | | vrf | | vrf-name] [private]

Syntax Description


ipv4	(Optional) Specifies an IPv4 address family.
afi-all	(Optional) Specifies all address families.
all	(Optional) Specifies all protocols for a given address family.
protocol	(Optional) Specifies a routing protocol. For the IPv4 address family, the options are eigrp , bgp , isis , ospf , and rip .
default-context	(Optional) Displays default context information. This keyword is available when the eigrp or rip protocol is specified.
vrf `vrf-name`	(Optional) Displays VPN routing and forwarding (VRF) information for the specified process. This keyword is available when the eigrp or rip protocol is specified.
private	(Optional) Displays private EIGRP data. This keyword is available when the eigrp is specified.

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.2	This command was introduced.
Release 3.9.0	Asplain format for 4-byte Autonomous system numbers notation was supported. The input parameters and output were modified to display 4-byte autonomous system numbers and extended communities in either asplain or asdot notations.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the show protocols command to get information about the protocols running on the router and to quickly determine which protocols are active. The command is designed to summarize the important characteristics of the running protocol, and command output varies depending on the specific protocol selected.

For EIGRP, the command output lists the instance number, default AS context, router ID, default networks, distance, maximum paths, and so on.

Task ID


Task ID	Operations
EIGRP	read

Examples

The following is sample output from the show protocols eigrp command:


  RP/0/RSP0/CPU0:router# show protocols eigrp
  
  Routing Protocol: EIGRP, instance 1
   Default context AS: 1, Router ID: 192.168.0.22
    Address Family: IPv4
     Default networks not flagged in outgoing updates
     Default networks not accepted from incoming updates
     Distance: internal 90, external 170
     Maximum paths: 4
     EIGRP metric weight K1=1, K2=0, K3=1, K4=0, K5=0
     EIGRP maximum hopcount 100
     EIGRP maximum metric variance 1
     EIGRP NSF: enabled
      NSF-aware route hold timer is 240s
      NSF signal timer is 20s
      NSF converge timer is 120s
      Time since last restart is 01:01:21
     SIA Active timer is 180s
     Interfaces:
      GigabitEthernet0/6/0/0

This table describes the significant fields shown in the display.

Table 9. show protocols Field Descriptions
Field	Descriptions
instance	AS number of the instance. Range for 2-byte Autonomous system numbers (ASNs) is 1 to 65535. Range for 4-byte Autonomous system numbers (ASNs) in asplain format is 1 to 4294967295. Range for 4-byte Autonomous system numbers (ASNs) is asdot format is 1.0 to 65535.65535.
AS	AS number of this context. Range for 2-byte Autonomous system numbers (ASNs) is 1 to 65535. Range for 4-byte Autonomous system numbers (ASNs) in asplain format is 1 to 4294967295. Range for 4-byte Autonomous system numbers (ASNs) is asdot format is 1.0 to 65535.65535.
Address Family	Address family for which the configuration status is shown.
Default Networks Candidate	Default network acceptance and announcement behavior.
Distance	Administrative distance of EIGRP routes.
Maximum paths	Maximum paths installed in RIB for a route.
Metric Weight	Current metric weights used by EIGRP.
Maximum hopcount	Maximum hop count accepted by EIGRP.
Variance	Metric variance used to find feasible paths for a route.
Route hold time	Time duration for which routes learned from a neighbor are held without deletion while the neighbor is undergoing a graceful restart.
signal time	Nonstop forwarding signal time.
converge time	Nonstop forwarding convergence time.
SIA Active time	Active time period for SIA.
Interfaces	List of interfaces configured for EIGRP.

site-of-origin (EIGRP)

To configure the Site of Origin (SoO) filtering on an Enhanced Interior Gateway Routing Protocol (EIGRP) interface, use the site-of-origin command in interface configuration mode. To disable SoO filtering on an interface, use the no form of this command.

site-of-origin {as-number : number | ip-address : number}

no site-of-origin

Syntax Description


`as-number` :	Autonomous system number. Range for 2-byte Autonomous system numbers (ASNs) is 1 to 65535. Range for 4-byte Autonomous system numbers (ASNs) in asplain format is 1 to 4294967295. Range for 4-byte Autonomous system numbers (ASNs) is asdot format is 1.0 to 65535.65535. The colon is used to separate the autonomous system number and network number.
number	Network number. Range is from 0 to 4294967295 when a 2-byte AS number is used. Range is from 0 to 65535 when a 4-byte AS number is used.
`ip-address` :	IP address in four-part, dotted-decimal notation. The colon is used to separate the IP address and network number.

Command Default

No default behavior or values

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.
Release 3.9.0	Asplain format for 4-byte Autonomous system numbers notation was supported.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

An EIGRP process must be capable of retrieving the SoO attribute on routes redistributed from the Border Gateway Protocol (BGP) when required to support complex topologies that include MPLS VPN links between sites with backdoor links.

Use the site-of-origin command to set an SoO BGP extended community attribute that is used to identify routes that have originated from a site so that the readvertisement of that prefix back to the source site can be prevented. The SoO extended community uniquely identifies the site from which a provider edge (PE) router has learned a route.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure SoO filtering on an EIGRP interface:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) vrf customer1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# interface GigabitEthernet 0/1/0/0
  RP/0/RSP0/CPU0:router(config-eigrp--vrf-af-if)# site-of-origin 10.0.0.1:20

split-horizon disable (EIGRP)

To disable split horizon for an Enhanced Interior Gateway Routing Protocol (EIGRP) process, use the split-horizon disable command in interface configuration mode. To enable split horizon, use the no form of this command.

split-horizon disable

no split-horizon disable

Syntax Description

This command has no keywords or arguments.

Command Default

Split horizon is enabled for an EIGRP process.

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to disable split horizon an a GigabitEthernet link:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/0
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# split-horizon disable

stub (EIGRP)

To configure a router as a stub for Enhanced Interior Gateway Routing Protocol (EIGRP), use the stub command in the appropriate configuration mode. To disable this function, use the no form of this command.

stub [receive-only | [connected] [redistributed] [static] [summary]]

no stub [receive-only | [connected] [redistributed] [static] [summary]]

Syntax Description


receive-only	(Optional) Sets the router as a receive-only neighbor.
connected	(Optional) Advertises connected routes.
redistributed	(Optional) Advertises redistributed routes from other protocols and autonomous systems.
static	(Optional) Advertises static routes.
summary	(Optional) Advertises summary routes.

Command Default

Stub routing is disabled.

When stub routing is specified, connected and summary routes are advertised by default.

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the stub command to configure a router as a stub in which the router directs all IP traffic to a distribution router.

The stub command can be modified with several options, and these options can be used in any combination except for the receive-only keyword.

The receive-only keyword restricts the router from sharing any of its routes with any other router in that EIGRP autonomous system and does not permit any other option to be specified because it prevents any type of route from being sent. The four other optional keywords ( connected , static , summary , and redistributed ) can be used in any combination but cannot be used with the receive-only keyword. If any of these four keywords is used with the stub command, only the route types specified by the particular keyword or keywords are sent. Route types specified by the nonused keyword or keywords are not sent.

The connected keyword permits EIGRP stub routing to send connected routes. If all the connected routes are not covered by EIGRP interfaces, it may be necessary to redistribute connected routes with the redistribute connected command under the EIGRP process. This option is enabled by default.

The static keyword permits EIGRP stub routing to send static routes. Without the configuration of this option, EIGRP does not send any static routes. You may still need to redistribute static routes with the redistribute static command.

The summary keyword permits EIGRP stub routing to send summary routes. Summary routes can be created manually with the summary address command or automatically at a major network border router with the auto-summary command enabled. This option is enabled by default.

The redistributed keyword permits EIGRP stub routing to send other routing protocols and autonomous systems. Without the configuration of this option, EIGRP does not advertise redistributed routes.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure, as a stub, the router that advertises connected and summary routes:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# stub

The following example shows how to configure the router as a receive-only neighbor (connected, summary, and static routes are not sent):


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# stub receive-only

Related Commands


Command	Description
redistribute (EIGRP)	Redistributes routes from one routing domain into EIGRP.
summary-address (EIGRP)	Configures a summary aggregate address for the specified EIGRP interface.
auto-summary (EIGRP)	Allows automatic summarization of subnet routes into network-level routes for an EIGRP process.

summary-address (EIGRP)

To configure a summary aggregate address for the specified Enhanced Interior Gateway Routing Protocol (EIGRP) interface, use the summary-address command in interface configuration mode. To disable a configuration, use the no form of this command.

summary-address ip-address {/ length | mask} [admin-distance]

no summary-address ip-address {/ length | mask}

Syntax Description


`ip-address`	The IP address argument specifies the summary IP address to apply to an interface in four-part, dotted-decimal notation.
`/` `length`	Prefix length, which can be indicated as a slash (/) and number. For example, /8 indicates that the first eight bits in the IP prefix are network bits. If `length` is used, the slash is required.
`mask`	IP address mask.
`admin-distance`	(Optional) Administrative distance. A value from 1 to 255.

Command Default

An administrative distance of 5 is applied to EIGRP summary routes.

No summary addresses are predefined.

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The summary-address command is used to configure interface-level address summarization. EIGRP summary routes are given an administrative distance of 5. The administrative distance is used to advertise a summary without installing it in the routing table.

By default, EIGRP summarizes subnet routes to the network level. The no auto-summary command can be entered to configure subnet level summarization.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure an administrative distance of 95 on an EIGRP interface for the 192.168.0.0/16 summary address:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# interface GigabitEthernet 0/1/0/0
  RP/0/RSP0/CPU0:router(config-eigrp-af-if)# summary-address 192.168.0.0/16 95

Related Commands


Command	Description
auto-summary (EIGRP)	Allows automatic summarization of subnet routes into network-level routes for an EIGRP process.

timers active-time

To adjust the Enhanced Interior Gateway Routing Protocol (EIGRP) routing wait time, use the timers active-time command in the appropriate configuration mode. To disable this function, use the timers active-time no form of the command.

timers active-time [time-limit | disabled]

no timers active-time

Syntax Description


`time-limit`	Active time limit (in minutes). Range is from 1 to 4294967295 minutes.
disabled	Disables the timers and permits the routing wait time to remain active indefinitely.

Command Default

Disabled

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the timers active-time command to control the time the router waits (after query is sent) before declaring the route to be in the stuck in active (SIA) state.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to configure an indefinite routing wait time on the specified EIGRP route:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# timers active-time disabled

timers nsf route-hold (EIGRP)

To set the timer that determines how long an NSF-aware Enhanced Interior Gateway Routing Protocol (EIGRP) router holds routes for an inactive peer, use the timers nsf route-hold command in the appropriate configuration mode. To return the route hold timer to the default value, use the no form of this command.

timers nsf route-hold seconds

no timers nsf route-hold

Syntax Description


`seconds`	Time, in seconds, that EIGRP holds routes for an inactive peer. Range is from 20 to 6000 seconds.

Command Default

EIGRP NSF awareness is enabled.

seconds :240

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.
Release 4.1.1	The default route hold time was changed from 240 seconds to 480 seconds.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the timers nsf route-hold command to set the maximum period of time that the NSF-aware router holds known routes for an NSF-capable neighbor during a switchover operation or a well-known failure condition. The route hold timer is configurable so that you can tune network performance and avoid undesired effects, such as packet loss on routes if the switchover operation takes too much time. When this timer expires, the NSF-aware router scans the topology table and discards any stale routes, allowing EIGRP peers to find alternate routes instead of waiting during a long switchover operation.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to set the route hold timer value for an NSF-aware router to 2 minutes (120 seconds):


RP/0/RSP0/CPU0:router(config)# router eigrp 1
RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
RP/0/RSP0/CPU0:router(config-eigrp-af)# timers nsf route-hold 120

variance

To control load balancing in an Enhanced Interior Gateway Routing Protocol (EIGRP)-based internetwork, use the variance command in the appropriate configuration mode. To reset the variance to the default value, use the no form of this command.

variance multiplier

no variance

Syntax Description


`multiplier`	Metric value used for load balancing. Range is from 1 to 128.

Command Default

multiplier : 1 (equal-cost load balancing)

Command Modes

IPv4 address family configuration

IPv4 VRF address family configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the variance command to set a variance on the EIGRP router so that the router can determine the feasibility of a potential route. A route is feasible if the next router in the path is closer to the destination than the current router and the metric for the entire path is within the variance. Only paths that are feasible can be used for load balancing and included in the routing table.

If the following two conditions are met, the route is considered feasible and can be added to the routing table:

The local best metric must be greater than the metric learned from the next router.
The multiplier times the local best metric for the destination must be greater than or equal to the metric through the next router.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to set a variance of 4:


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp) address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-af)# variance 4

vrf (EIGRP)

To define a VPN routing and forwarding (VRF) instance and enter VRF configuration mode, use the vrf command in router configuration mode. To remove a VRF instance, use the no form of this command.

vrf vrf-name

no vrf vrf-name

Syntax Description


`vrf-name`	VPN routing and forwarding instance.

Command Default

No VRFs are defined.

Command Modes

Router configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Use the vrf command to configure a VRF instance. A VRF instance is a collection of VPN routing and forwarding tables maintained at the provider edge (PE) router.

From VRF configuration mode, you must enter address family configuration mode and then issue commands, such as the auto-summary command.

A single EIGRP routing process can support multiple VRFs. The number of VRFs that can be configured is limited by available system resources on the router, which is determined by the number of VRFs, running processes, and available memory. However, only a single VRF can be supported by each VPN. Redistribution between different VRFs is not supported.

MPLS VPN support between PE and customer edge (CE) routers is configured only on PE routers that provide VPN services over the service provider backbone. The customer site does not require any changes to equipment or configurations to support the EIGRP VPN. Typically, a metric must be configured for routes to be advertised to the CE router. The metric can be configured under the route-policy for the redistribute protocol command or configured with the default-metric command.

You must remove IPv4/IPv6 addresses from an interface prior to assigning, removing, or changing a VRF on an IP interface. If this is not done in advance, any attempt to change the VRF on an IP interface is rejected.

Task ID


Task ID	Operations
eigrp	read, write

Examples

The following example shows how to enter IPv4 VRF address family configuration mode and identify EIGRP commands that can be issued from that mode.


  RP/0/RSP0/CPU0:router(config)# router eigrp 1
  RP/0/RSP0/CPU0:router(config-eigrp)# vrf vpn-1
  RP/0/RSP0/CPU0:router(config-eigrp-vrf)# address-family ipv4
  RP/0/RSP0/CPU0:router(config-eigrp-vrf-af)# ?
  
    auto-summary           Auto summarisation
    autonomous-system      Set the autonomous system of VRF
    commit                 Commit the configuration changes to running
    default-information    Handling of default route
    default-metric         Set metric of redistributed routes
    describe               Describe a command without taking real actions
    distance               Set distance for EIGRP routes
    do                     Run an exec command
    exit                   Exit from this submode
    interface              EIGRP interface configuration submode
    log-neighbor-changes   Enable/Disable EIGRP neighbor logging
    log-neighbor-warnings  Enable/Disable EIGRP neighbor warnings
    maximum-paths          Maximum paths
    maximum-prefix         Maximum number of IP prefixes acceptable in aggregate
    metric                 Modify EIGRP routing metrics and parameters
    neighbor               Neighbor prefix limits configuration
    no                     Negate a command or set its defaults
    redistribute           Redistribute another protocol
    route-policy           Configure inbound/outbound policies
    router-id              Set router ID
    show                   Show contents of configuration
    stub                   EIGRP stub
    timers                 Configure EIGRP timers
    variance               Control load balancing variance

Related Commands


Command	Description
default-metric (EIGRP)	Sets metrics for an EIGRP.
redistribute (EIGRP)	Injects routes from one routing domain EIGRP.

Bias-Free Language

Results

Chapter: EIGRP Commands

EIGRP Commands

address-family (EIGRP)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

authentication keychain

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

auto-summary (EIGRP)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

autonomous-system

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

bandwidth-percent (EIGRP)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

bfd fast-detect (EIGRP)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

bfd minimum-interval (EIGRP)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

bfd multiplier (EIGRP)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

clear eigrp neighbors

Syntax Description

Command Default

Command Modes

Command History