Cisco ONS 15454 Reference Manual, Release 8.0

DS1-14

YES

—

YES

—

YES

YES

YES

—

DS1N-14

YES

—

YES

—

YES

YES

YES

—

EC1-12 card

OC3 IR 4/STM1 SH 1310

OC3 IR/STM1 SH 1310-8

OC12 IR/STM4 SH1310

OC12 LR/STM4 LH1310

OC12 LR/STM4 LH 1550

OC12 IR/STM4 SH 1310-4

OC48 IR/STM16 SH AS 1310

OC48 LR/STM16 LH AS 1550

OC48 ELR/STM16 EH 100 GHz

OC48 ELR 200 GHz

OC192 SR/STM64 IO 1310

OC192 IR/STM64 SH 1550

OC192 LR/STM64 LH 1550

OC192 LR/STM64 LH ITU 15xx.xx

TXP_MR_10G

MXP_2.5G_10G

MXP_MR_2.5G

MXPP_MR_2.5G

MRC-12

MRC-2.5G-4

OC 192 - XFP

AISS-P

AIS Seconds Path (AISS-P) is a count of one-second intervals containing one or more alarm indication signal (AIS) defects.

BBE-PM

Path Monitoring Background Block Errors (BBE-PM) indicates the number of background block errors recorded in the optical transport network (OTN) path during the PM time interval.

BBE-SM

Section Monitoring Background Block Errors (BBE-SM) indicates the number of background block errors recorded in the OTN section during the PM time interval.

BBER-PM

Path Monitoring Background Block Errors Ratio (BBER-PM) indicates the background block errors ratio recorded in the OTN path during the PM time interval.

BBER-SM

Section Monitoring Background Block Errors Ratio (BBER-SM) indicates the background block errors ratio recorded in the OTN section during the PM time interval.

BIT-EC

Bit Errors Corrected (BIT-EC) indicated the number of bit errors corrected in the DWDM trunk line during the PM time interval.

CSS

Controlled Slip Seconds (CSS) indicates the count of the seconds when at least one or more controlled slips have occurred.

CSS-P

Controlled Slip Seconds Path (CSS-P) indicates the count of the seconds when at least one or more controlled slips have occurred.

CVCP-P

Code Violation CP-bit Path (CVCP-P) is a count of CP-bit parity errors occurring in the accumulation period.

CVCP-PFE

Code Violation CP-bit Path (CVCP-PFE) is a parameter that is counted when the three far-end block error (FEBE) bits in an M-frame are not all collectively set to 1.

CGV

Code Group Violations (CGV) is a count of received code groups that do not contain a start or end delimiter.

CV-L

Line Code Violation (CV-L) indicates the number of coding violations occurring on the line. This parameter is a count of bipolar violations (BPVs) and excessive zeros (EXZs) occurring over the accumulation period.

CV-P

Near-End STS Path Coding Violations (CV-P) is a count of BIP errors detected at the STS path layer (that is, using the B3 byte). Up to eight BIP errors can be detected per frame; each error increments the current CV-P second register.

CV-PFE

Far-End STS Path Coding Violations (CV-PFE) is a count of BIP errors detected at the STS path layer (that is, using the B3 byte). Up to eight BIP errors can be detected per frame; each error increments the current CV-PFE second register.

CVP-P

Code Violation Path (CVP-P) is a code violation parameter for M23 applications. CVP-P is a count of P-bit parity errors occurring in the accumulation period.

CV-S

Section Coding Violation (CV-S) is a count of bit interleaved parity (BIP) errors detected at the section layer (that is, using the B1 byte in the incoming SONET signal). Up to eight section BIP errors can be detected per STS-N frame; each error increments the current CV-S second register.

CV-V

Code Violation VT Layer (CV-V) is a count of the BIP errors detected at the VT path layer. Up to two BIP errors can be detected per VT superframe, with each error incrementing the current CV-V second register.

DCG

Data Code Groups (DCG) is a count of received data code groups that do not contain ordered sets.

ESA-P

Path Errored Seconds-A (ESA-P) is the count of 1-second intervals with exactly one CRC-6 error and no AIS or severely errored framing (SEF) defects.

ESB-P

Path Errored Seconds-B (Rx ESB-P) is a count of 1-second intervals with between 2 and 319 CRC-6 errors and no AIS or SEF.

ESCP-P

Errored Seconds CP-bit Path (ESCP-P) is a count of seconds containing one or more CP-bit parity errors, one or more SEF defects, or one or more AIS defects. ESCP-P is defined for the C-bit parity application.

ESCP-PFE

Far-End Errored Seconds CP-bit Path (ESCP-PFE) is a count of one-second intervals containing one or more M-frames with the three FEBE bits not all collectively set to 1 or one or more far-end SEF/AIS defects.

ES-L

Line Errored Seconds (ES-L) is a count of the seconds containing one or more anomalies (BPV + EXZ) and/or defects (that is, loss of signal) on the line.

ES-NP

ES-P

Near-End STS Path Errored Seconds (ES-P) is a count of the seconds when at least one STS path BIP error was detected. An AIS Path (AIS-P) defect (or a lower-layer, traffic-related, near-end defect) or a Loss of Pointer Path (LOP-P) defect can also cause an ES-P.

ES-PFE

Far-End STS Path Errored Seconds (ES-PFE) is a count of the seconds when at least one STS path BIP error was detected. An AIS-P defect (or a lower-layer, traffic-related, far-end defect) or an LOP-P defect can also cause an STS ES-PFE.

ES-PM

Path Monitoring Errored Seconds (ES-PM) indicates the errored seconds recorded in the OTN path during the PM time interval.

ESP-P

Errored Seconds Path (ESP-P) is a count of seconds containing one or more P-bit parity errors, one or more SEF defects, or one or more AIS defects.

ESR-PM

Path Monitoring Errored Seconds Ratio (ESR-PM) indicates the errored seconds ratio recorded in the OTN path during the PM time interval.

ESR-SM

Section Monitoring Errored Seconds Ratio (ESR-SM) indicates the errored seconds ratio recorded in the OTN section during the PM time interval.

ES-S

Section Errored Seconds (ES-S) is a count of the number of seconds when at least one section-layer BIP error was detected or an SEF or loss of signal (LOS) defect was present.

ES-SM

Section Monitoring Errored Seconds (ES-SM) indicates the errored seconds recorded in the OTN section during the PM time interval.

ES-V

Errored Seconds VT Layer (ES-V) is a count of the seconds when at least one VT Path BIP error was detected. An AIS Virtual Tributary (VT) (AIS-V) defect (or a lower-layer, traffic-related, near-end defect) or an LOP VT (LOP-V) defect can also cause an ES-V.

FC-L

Line Failure Count (FC-L) is a count of the number of near-end line failure events. A failure event begins when an AIS Line (AIS-L) failure is declared or when a lower-layer, traffic-related, near-end failure is declared. This failure event ends when the failure is cleared. A failure event that begins in one period and ends in another period is counted only in the period where it begins.

FC-P

Near-End STS Path Failure Counts (FC-P) is a count of the number of near-end STS path failure events. A failure event begins when an AIS-P failure, an LOP-P failure, a UNEQ-P failure, or a Section Trace Identifier Mismatch Path (TIM-P) failure is declared. A failure event also begins if the STS PTE that is monitoring the path supports Three-Bit (Enhanced) Remote Failure Indication Path Connectivity (ERFI-P-CONN) for that path. The failure event ends when these failures are cleared.

FC-PFE

Far-End STS Path Failure Counts (FC-PFE) is a count of the number of near-end STS path failure events. A failure event begins when an AIS-P failure, an LOP-P failure, a UNEQ-P failure, or a TIM-P failure is declared. A failure event also begins if the STS PTE that is monitoring the path supports ERFI-P-CONN for that path. The failure event ends when these failures are cleared.

FC-PM

Path Monitoring Failure Counts (FC-PM) indicates the failure counts recorded in the OTN path during the PM time interval.

FC-SM

Section Monitoring Failure Counts (FC-SM) indicates the failure counts recorded in the OTN section during the PM time interval.

IOS

Idle Ordered Sets (IOS) is a count of received packets containing idle ordered sets.

IPC

Invalid Packets (IPC) is the count of received packets that contain errored data code groups that have start and end delimiters.

LBCL-MIN

Laser Bias Current Line—Minimum (LBCL-MIN) is the minimum percentage of laser bias current.

LBCL-AVG

Laser Bias Current Line—Average (LBCL-AVG) is the average percentage of laser bias current.

LBCL-MAX

Laser Bias Current Line—Maximum (LBCL-MAX) is the maximum percentage of laser bias current.

LOFC

Loss of Frame Count (LOFC)

LOSS-L

Line Loss of Signal (LOSS-L) is a count of one-second intervals containing one or more LOS defects.

NIOS

Non-Idle Ordered Sets (NIOS) is a count of received packets containing non-idle ordered sets.

NPJC-PDET

Negative Pointer Justification Count, STS Detected (NPJC-PDET), formerly Pointer Justification Negative (PJNEG)

NPJC-PDET-P

Negative Pointer Justification Count, STS Path Detected (NPJC-PDET-P) is a count of the negative pointer justifications detected on a particular path in an incoming SONET signal.

NPJC-PGEN-P

Negative Pointer Justification Count, STS Path Generated (NPJC-PGEN-P) is a count of the negative pointer justifications generated for a particular path to reconcile the frequency of the SPE with the local clock.

OPR

Optical Power Received (OPR) is the measure of average optical power received as a percentage of the nominal OPR.

OPR-AVG

Average Receive Optical Power (dBm)

OPR-MAX

Maximum Receive Optical Power (dBm)

OPR-MIN

Minimum Receive Optical Power (dBm)

OPT

Optical Power Transmitted (OPT) is the measure of average optical power transmitted as a percentage of the nominal OPT.

OPT-AVG

Average Transmit Optical Power (dBm)

OPT-MAX

Maximum Transmit Optical Power (dBm)

OPT-MIN

Minimum Transmit Optical Power (dBm)

OPWR-AVG

Optical Power - Average (OPWR-AVG) is the measure of average optical power on the unidirectional port.

OPWR-MAX

Optical Power - Maximum (OPWR-MAX) is the measure of maximum value of optical power on the unidirectional port.

OPWR-MIN

Optical Power - Minimum (OPWR-MIN) is the measure of minimum value of optical power on the unidirectional port.

PJCDIFF-P

Pointer Justification Count Difference, STS Path (PJCDIFF-P) is the absolute value of the difference between the total number of detected pointer justification counts and the total number of generated pointer justification counts. That is, PJCDiff-P is equal to (PPJC-PGEN-P - NPJC-PGEN-P) - (PPJC-PDET-P - NPJC-PDET-P).

PPJC-PDET

Pointer Justification STS Detected (PPJC-PDET), formerly Pointer Justification Positive (PJPOS).

PPJC-PDET-P

Positive Pointer Justification Count, STS Path Detected (PPJC-PDET-P) is a count of the positive pointer justifications detected on a particular path in an incoming SONET signal.

PPJC-PGEN-P

Positive Pointer Justification Count, STS Path Generated (PPJC-PGEN-P) is a count of the positive pointer justifications generated for a particular path to reconcile the frequency of the SPE with the local clock.

PJCS-PDET-P

Pointer Justification Count Seconds, STS Path Detect (NPJCS-PDET-P) is a count of the one-second intervals containing one or more PPJC-PDET or NPJC-PDET.

PJCS-PGEN-P

Pointer Justification Count Seconds, STS Path Generate (PJCS-PGEN-P) is a count of the one-second intervals containing one or more PPJC-PGEN or NPJC-PGEN.

PSC

In a 1 + 1 protection scheme for a working card, Protection Switching Count (PSC) is a count of the number of times service switches from a working card to a protection card plus the number of times service switches back to the working card.

For a protection card, PSC is a count of the number of times service switches to a working card from a protection card plus the number of times service switches back to the protection card. The PSC PM parameter is only applicable if revertive line-level protection switching is used.

PSC-R

In a four-fiber bidirectional line switched ring (BLSR), Protection Switching Count-Ring (PSC-R) is a count of the number of times service switches from a working line to a protection line plus the number of times it switches back to a working line. A count is only incremented if ring switching is used.

PSC-S

In a four-fiber BLSR, Protection Switching Count-Span (PSC-S) is a count of the number of times service switches from a working line to a protection line plus the number of times it switches back to the working line. A count is only incremented if span switching is used.

PSC-W

For a working line in a two-fiber BLSR, Protection Switching Count-Working (PSC-W) is a count of the number of times traffic switches away from the working capacity in the failed line and back to the working capacity after the failure is cleared. PSC-W increments on the failed working line and PSC increments on the active protect line.

For a working line in a four-fiber BLSR, PSC-W is a count of the number of times service switches from a working line to a protection line plus the number of times it switches back to the working line. PSC-W increments on the failed line and PSC-R or PSC-S increments on the active protect line.

PSD

Protection Switching Duration (PSD) applies to the length of time, in seconds, that service is carried on another line. For a working line, PSD is a count of the number of seconds that service was carried on the protection line.

For the protection line, PSD is a count of the seconds that the line was used to carry service. The PSD PM is only applicable if revertive line-level protection switching is used.

PSD-R

In a four-fiber BLSR, Protection Switching Duration-Ring (PSD-R) is a count of the seconds that the protection line was used to carry service. A count is only incremented if ring switching is used.

PSD-S

In a four-fiber BLSR, Protection Switching Duration-Span (PSD-S) is a count of the seconds that the protection line was used to carry service. A count is only incremented if span switching is used.

SASCP-P

SEF/AIS Seconds CP-bit Path (SASCP-P) is a count of one-second intervals containing one or more SEFs or one or more AIS defects on the path.

SASP

SEF/AIS Seconds (SASP) is a count of one-second intervals containing one or more SEFs or one or more AIS defects on the path.

SASP-P

SEF/AIS Seconds Path (SASP-P) is a count of one-second intervals containing one or more SEFs or one or more AIS defects on the path.

SEF-S

Severely Errored Framing Seconds (SEFS-S) is a count of the seconds when an SEF defect was present. An SEF defect is expected to be present during most seconds when an LOS or loss of frame (LOF) defect is present. However, there can be situations when the SEFS-S parameter is only incremented based on the presence of the SEF defect.

SESCP-P

Severely Errored Seconds CP-bit Path (SESCP-P) is a count of seconds containing more than 44 CP-bit parity errors, one or more SEF defects, or one or more AIS defects.

SESCP-PFE

Severely Errored Seconds CP-bit Path (SESCP-PFE) is a count of one-second intervals containing one or more far-end SEF/AIS defects, or one or more 44 M-frames with the three FEBE bits not all collectively set to 1.

SES-L

Line Severely Errored Seconds (SES-L) is a count of the seconds containing more than a particular quantity of anomalies (BPV + EXZ > 44) and/or defects on the line.

SES-P

Near-End STS Path Severely Errored Seconds (SES-P) is a count of the seconds when K (2400) or more STS path BIP errors were detected. An AIS-P defect (or a lower-layer, traffic-related, near-end defect) or an LOP-P defect can also cause an SES-P.

SES-PFE

Far-End STS Path Severely Errored Seconds (SES-PFE) is a count of the seconds when K (2400) or more STS path BIP errors were detected. An AIS-P defect (or a lower-layer, traffic-related, far-end defect) or an LOP-P defect can also cause an SES-PFE.

SES-PM

Path Monitoring Severely Errored Seconds (SES-PM) indicates the severely errored seconds recorded in the OTN path during the PM time interval.

SESP-P

Severely Errored Seconds Path (SESP-P) is a count of seconds containing more than 44 P-bit parity violations, one or more SEF defects, or one or more AIS defects.

SES-S

Section Severely Errored Seconds (SES-S) is a count of the seconds when K (see Telcordia GR-253 for value) or more section-layer BIP errors were detected or an SEF or LOS defect was present.

SES-SM

Section Monitoring Severely Errored Seconds (SES-SM) indicates the severely errored seconds recorded in the OTN section during the PM time interval.

SESR-PM

Path Monitoring Severely Errored Seconds Ratio (SESR-PM) indicates the severely errored seconds ratio recorded in the OTN path during the PM time interval.

SESR-SM

Section Monitoring Severely Errored Seconds Ratio (SESR-SM) indicates the severely errored seconds ratio recorded in the OTN section during the PM time interval.

SES-V

Severely Errored Seconds VT Layer (SES-V) is a count of seconds when K (600) or more VT Path BIP errors were detected. An AIS-V defect (or a lower-layer, traffic-related, near-end defect) or an LOP-V defect can also cause SES-V.

UAS-L

Line Unavailable Seconds (UAS-L) is a count of the seconds when the line is unavailable. A line becomes unavailable when ten consecutive seconds occur that qualify as SES-Ls, and it continues to be unavailable until ten consecutive seconds occur that do not qualify as SES-Ls.

UASCP-P

Unavailable Seconds CP-bit Path (UASCP-P) is a count of one-second intervals when the DS-3 path is unavailable. A DS-3 path becomes unavailable when ten consecutive SESCP-Ps occur. The ten SESCP-Ps are included in unavailable time. After the DS-3 path becomes unavailable, it becomes available again when ten consecutive seconds with no SESCP-Ps occur. The ten seconds with no SESCP-Ps are excluded from unavailable time.

UASCP-PFE

Unavailable Seconds CP-bit Path (UASCP-PFE) is a count of one-second intervals when the DS-3 path becomes unavailable. A DS-3 path becomes unavailable when ten consecutive far-end CP-bit SESs occur. The ten CP-bit SESs are included in unavailable time. After the DS-3 path becomes unavailable, it becomes available again when ten consecutive seconds occur with no CP-bit SESs. The ten seconds with no CP-bit SESs are excluded from unavailable time.

UAS-P

Near-End STS Path Unavailable Seconds (UAS-P) is a count of the seconds when the STS path was unavailable. An STS path becomes unavailable when ten consecutive seconds occur that qualify as SES-Ps, and continues to be unavailable until ten consecutive seconds occur that do not qualify as SES-Ps.

UAS-PFE

Far-End STS Path Unavailable Seconds (UAS-PFE) is a count of the seconds when the STS path was unavailable. An STS path becomes unavailable when ten consecutive seconds occur that qualify as SES-PFEs, and continues to be unavailable until ten consecutive seconds occur that do not qualify as SES-PFEs.

UAS-PM

Path Monitoring Unavailable Seconds (UAS-PM) indicates the unavailable seconds recorded in the OTN path during the PM time interval.

UASP-P

Unavailable Seconds Path (UASP-P) is a count of one-second intervals when the DS-3 path is unavailable. A DS-3 path becomes unavailable when ten consecutive SESP-Ps occur. The ten SESP-Ps are included in unavailable time. After the DS-3 path becomes unavailable, it becomes available again when ten consecutive seconds with no SESP-Ps occur. The ten seconds with no SESP-Ps are excluded from unavailable time.

UAS-SM

Section Monitoring Unavailable Seconds (UAS-SM) indicates the unavailable seconds recorded in the OTN section during the PM time interval.

UAS-V

Unavailable Seconds VT Layer (UAS-V) is a count of the seconds when the VT path was unavailable. A VT path becomes unavailable when ten consecutive seconds occur that qualify as SES-Vs, and it continues to be unavailable until ten consecutive seconds occur that do not qualify as SES-Vs.

UNC-WORDS

Uncorrectable Words (UNC-WORDS) is the number of uncorrectable words detected in the DWDM trunk line during the PM time interval.

VPC

Valid Packets (VPC) is a count of received packets that contain non-errored data code groups that have start and end delimiters.

CV-S
ES-S
SES-S
SEF-S

CV-L
ES-L
SES-L
UAS-L
FC-L

CV-P
ES-P
SES-P
UAS-P
FC-P
PPJC-PDET-P
NPJC-PDET-P
PPJC-PGEN-P
NPJC-PGEN-P
PJCS-PDET-P
PJCS-PGEN-P
PJC-DIFF-P

CV-LFE
ES-LFE
SES-LFE
UAS-LFE
FC-LFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

CV-L
ES-L
SES-L
LOSS-L

CV-L
ES-L
SES-L
LOSS-L

AISS-P
CV-P
ES-P
SES-P
SAS-P
UAS-P
CSS-P
ESA-P
ESB-P
SEFS-P

AISS-P
CV-P
ES-P
SES-P
UAS-P
BBER-P
SESR-P
ESR-P

CV-P
ES-P
SES-P
UAS-P
FC-P

ES-PFE
ESA-PFE
ESB-PFE
CV-PFE
CSS-PFE
SEFS-PFE
SES-PFE
UAS-PFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

ES-NP
ES-NPFE
SES-NP
SES-NPFEUAS-NP
UAS-NPFE

CSS
ES
SES
BES
UAS
LOFC

CV-L
ES-L
SES-L
LOSS-L

CV-L
ES-L

AISS-P
CV-P
ES-P
FC-P
SAS-P
SES-P
UAS-P
CSS-P
ESA-P
ESB-P
SEFS-P

AISS-P
CV-P
ES-P
FC-P
SAS-P
SES-P
UAS-P

CV-V
ES-V
SES-V
UAS-V
FC-V

CV-P
ES-P
SES-P
UAS-P
FC-P

ES-PFE
ESA-PFE
ES-B-PFE
CV-PFE
CSS-PFE
SEFS-PFE
SES-PFE
UAS-PFE

CV-VFE
ES-VFE
SES-VFE
UAS-VFE
FC-VFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

CV-L
ES-L
SES-L
LOSS-L

CV-P
ES-P
SES-P
UAS-P
FC-P

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

CV-L
ES-L
SES-L
LOSS-L

AISS-P
CV-P
ES-P
SAS-P²
SES-P
UAS-P
CVCP-P
ESCP-P
SASCP-P³
SESCP-P
UASCP-P

CV-P
ES-P
SES-P
UAS-P
FC-P

CVCP-PFE
ESCP-PFE
SASCP-P
SESCP-PFE
UASCP-PFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

¹ The C-bit PMs (PMs that contain the text "CP-P") are applicable only if the line format is C-bit.

² DS3(N)-12E cards support SAS-P only on the receive (Rx) path.

³ The SASCP parameter is also displayed as "undefined" for near-end parameter though it is a far-end parameter.

CV-L
ES-L
SES-L
LOSS-L

AISSP-P
CVP-P
ESP-P
SASP-P²
SESP-P
UASP-P
CVCP-P
ESCP-P
SASCP-P³
SESCP-P
UASCP-P

CV-P
ES-P
SES-P
UAS-P
FC-P

CVCP-PFE
ESCP-PFE
SASCP-PFE
SESCP-PFE
UASCP-PFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

¹ The C-Bit PMs (PMs that contain the text "CP-P") are applicable only if the line format is C-Bit.

² DS3i-N-12 cards support SAS-P only on the Rx path.

³ The SASCP parameter is also displayed as "undefined" for near-end parameter though it is a far-end parameter.

CV-L
ES-L
SES-L
LOSS-L

AISS-P
CVP-P
ESP-P
SASP-P³
SESP-P
UASP-P
ESCP-P
SASCP-P⁴
SESCP-P
UASCP-P
CVCP-P

AISS-P
ES-P
SAS-P³
SES-P
UAS-P

CV-V
ES-V
SES-V
UAS-V

CV-P
ES-P
SES-P
UAS-P
FC-P

CVCP-PFE
ESCP-PFE
SASCP-PFE
SESCP-PFE
UASCP-PFE

CV-VFE
ES-VFE
SES-VFE
UAS-VFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

ES-NP

ES-NPFE

SES-NP

SES-NPFE

UAS-NP

UAS-NPFE

¹ The C-Bit PMs (PMs that contain the text "CP-P") are applicable only if the line format is C-Bit.

² Parameter received from far-end direction only.

³ DS3XM-6 cards support SAS-P only on the Rx path.

⁴ The SASCP parameter is also displayed as "undefined" for near-end parameter though it is a far-end parameter.

CV-L
ES-L
SES-L
LOSS-L

AISS-P
CV-P
ES-P
SAS-P³
SES-P
UAS-P
ESCP-P
SESCP-P
UASCP-P
CVCP-P

AISS-P
CV-P
ES-P
FC-P
SAS-P³
SES-P
UAS-P
CSS-P
ESA-P
ESB-P
SEFS-P

CV-V
ES-V
SES-V
UAS-V

CV-P
ES-P
SES-P
UAS-P
FC-P

CVCP-PFE
ESCP-PFE
SASCP-PFE⁴
SESCP-PFE
UASCP-PFE

CV-VFE
ES-VFE
SES-VFE
UAS-VFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

CSS
ES
SES
BES
UAS
LOFC

ES-NP

ES-NPFE

SES-NP

SES-NPFE

UAS-NP

UAS-NPFE

¹ The C-Bit PMs (PMs that contain the text "CP-P") are applicable only if the line format is C-Bit.

² Parameter received from far-end direction only.

³ DS3XM-12 cards support SAS-P only on the Rx path.

⁴ The SASCP parameter is also displayed as "undefined" for near-end parameter though it is a far-end parameter.

CV-L
ES-L
SES-L
LOSS-L

AISS-P
CVP-P
ESP-P
SASP-P²
SESP-P
UASP-P
ESCP-P
SASCP-P³
SESCP-P
UASCP-P
CVCP-P

CV-P
ES-P
SES-P
UAS-P
FC-P

CVCP-PFE
ESCP-PFE
SASCP-PFE
SESCP-PFE
UASCP-PFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

¹ The C-Bit PMs (PMs that contain the text "CP-P") are applicable only if the line format is C-Bit.

² DS3/EC1-48 cards support SAS-P only on the Rx path.

³ The SASCP parameter is also displayed as "undefined" for near-end parameter though it is a far-end parameter.

Link Status

Indicates whether link integrity is present; up means present, and down means not present.

ifInOctets

Number of bytes received since the last counter reset.

ifInUcastPkts

Number of unicast packets received since the last counter reset.

ifInErrors

The number of inbound packets (or transmission units) that contained errors preventing them from being deliverable to a higher-layer protocol.

ifOutOctets

Number of bytes transmitted since the last counter reset.

ifOutUcastPkts

Number of unicast packets transmitted.

dot3StatsAlignmentErrors

A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check.

dot3StatsFCSErrors

A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check.

dot3StatsFrameTooLong

A count of frames received on a particular interface that exceed the maximum permitted frame size.

etherStatsUndersizePkts

The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.

etherStatsFragments

The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

Note It is entirely normal for etherStatsFragments to increment. This is because it counts both runts (which are normal occurrences due to collisions) and noise hits.

etherStatsPkts64Octets

The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).

etherStatsPkts65to127
Octets

The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts128to255
Octets

The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts256to511
Octets

The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts512to1023Octets

The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts1024to1518Octets

The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsOversizePkts

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. Note that for tagged interfaces, this number becomes 1522 bytes.

etherStatsJabbers

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

etherStatsOctets

The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets

etherStatsCRCAlign
Errors

The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

STS-1

51840000

STS-3c

155000000

STS-6c

311000000

STS-12c

622000000

1 minute

60

15 minutes

32

1 hour

24

1 day (24 hours)

7

Time Last Cleared

A time stamp indicating the last time statistics were reset.

Link Status

Indicates whether the Ethernet link is receiving a valid Ethernet signal (carrier) from the attached Ethernet device; up means present, and down means not present.

Rx Packets

Number of packets received since the last counter reset.

Rx Bytes

Number of bytes received since the last counter reset.

Tx Packets

Number of packets transmitted since the last counter reset.

Tx Bytes

Number of bytes transmitted since the last counter reset.

Rx Total Errors

Total number of receive errors.

Rx FCS

Number of packets with a FCS error. FCS errors indicate frame corruption during transmission.

Rx Alignment

Number of packets with received incomplete frames.

Rx Runts

Measures undersized packets with bad CRC errors.

Rx Shorts

Measures undersized packets with good CRC errors.

Rx Jabbers

The total number of frames received that exceed the 1548-byte maximum and contain CRC errors.

Rx Giants

Number of packets received that are greater than 1530 bytes in length.

Rx Pause Frames

Number of received Ethernet IEEE 802.3z pause frames.

Tx Pause Frames

Number of transmitted IEEE 802.3z pause frames.

Rx Pkts Dropped Internal Congestion

Number of received packets dropped due to overflow in G-Series frame buffer.

Tx Pkts Dropped Internal Congestion

Number of transmit queue drops due to drops in the G-Series frame buffer.

HDLC Errors

High-level data link control (HDLC) errors received from SONET/SDH (see Note).

Rx Unicast Packets

Number of unicast packets received since the last counter reset.

Tx Unicast Packets

Number of unicast packets transmitted.

Rx Multicast Packets

Number of multicast packets received since the last counter reset.

Tx Multicast Packets

Number of multicast packets transmitted.

Rx Broadcast Packets

Number of broadcast packets received since the last counter reset.

Tx Broadcast Packets

Number or broadcast packets transmitted.

ifInOctets

Number of bytes received since the last counter reset.

rxTotalPackets

Number of packets received.

ifInUcastPkts

Number of unicast packets received since the last counter reset.

ifInMulticast Pkts

Number of multicast packets received since the last counter reset.

ifInBroadcast Pkts

Number of broadcast packets received since the last counter reset.

ifInDiscards

The number of inbound packets that were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.

ifInErrors

The number of inbound packets (or transmission units) that contained errors preventing them from being deliverable to a higher-layer protocol.

ifOutOctets

Number of bytes transmitted since the last counter reset.

txTotalPkts

Number of transmitted packets.

ifOutUcast Pkts

Number of unicast packets transmitted.

ifOutMulticast Pkts

Number of multicast packets transmitted.

ifOutBroadcast Pkts

Number or broadcast packets transmitted.

dot3StatsAlignmentErrors

A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check.

dot3StatsFCSErrors

A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check.

dot3StatsSingleCollisionFrames

A count of successfully transmitted frames on a particular interface for which transmission is inhibited by exactly on collision.

dot3StatsFrameTooLong

A count of frames received on a particular interface that exceed the maximum permitted frame size.

etherStatsUndersizePkts

The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.

etherStatsOversizePkts

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. Note that for tagged interfaces, this number becomes 1522 bytes.

etherStatsFragments

The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

Note Note: It is entirely normal for etherStatsFragments to increment. This is because it counts both runts (which are normal occurrences due to collisions) and noise hits.

etherStatsPkts64Octets

The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).

etherStatsPkts65to127Octets

The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts128to255Octets

The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts256to511Octets

The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts512to1023Octets

The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts1024to1518Octets

The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsBroadcastPkts

The total number of good packets received that were directed to the broadcast address. Note that this does not include multicast packets.

etherStatsMulticastPkts

The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.

etherStatsJabbers

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

etherStatsOctets

The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets.

etherStatsCollissions

Number of transmit packets that are collisions; the port and the attached device transmitting at the same time caused collisions.

etherStatsCRCAlignErrors

The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

etherStatsDropEvents

Number of received frames dropped at the port level.

rx PauseFrames¹

Number of received Ethernet 802.3z pause frames.

mediaIndStatsOversize
Dropped1

Number of received oversized packages that are dropped.

mediaIndStatsTxFrames
TooLong1

Number of received frames that are too long. The maximum is the programmed max frame size (for virtual SAN [VSAN] support); if the maximum frame size is set to default, then the maximum is a 2112 byte payload plus the 36 byte header, which is a total of 2148 bytes.

¹ ML100T-12, ML1000-2 only

ifInOctets

Number of bytes received since the last counter reset.

rxTotalPkts

Number of packets received.

ifOutOctets

Number of bytes transmitted since the last counter reset.

tx TotalPkts

Number of transmitted packets.

etherStatsDropEvents

Number of received frames dropped at the port level.

rxPktsDropped Internal
Congestion

Number of received packets dropped due to overflow in frame buffer.

mediaIndStatsRxFramesTruncated

Number of received frames with a length of 36 bytes or less.

mediaIndStatsRxFramesTooLong

Number of received frames that are too long. The maximum is the programmed maximum frame size (for VSAN support); if the maximum frame size is set to default, then the maximum is the 2112 byte payload plus the 36 byte header, which is a total of 2148 bytes.

mediaIndStatsRxFramesBadCRC

Number of received frames with CRC errors.

mediaIndStatsRxShort
Pkts

Number of received packets that are too small.

hdlcInOctets

Number of bytes received (from the SONET/SDH path) prior to the bytes undergoing HLDC decapsulation by the policy engine.

hdlcRxAborts

Number of received packets aborted on input.

hdlcOutOctets

Number of bytes transmitted (to the SONET/SDH path) after the bytes undergoing HLDC encapsulation by the policy engine.

etherStatsDropEvents

Number of received frames dropped at the port level.

rx PktsDroppedInternal
Congestion

Number of received packets dropped due to overflow in the frame buffer.

gfpStatsRxFrame

Number of received GFP frames.

gfpStatsTxFrame

Number of transmitted GFP frames.

gfpStatsRxOctets

Number of GFP bytes received.

gfpStatsTxOctets

Number of GFP bytes transmitted.

gfpStatsRxSBitErrors

Sum of all the single bit errors. In the GFP CORE HDR at the GFP-T receiver, these are correctable.

gfpStatsRxMBitErrors

Sum of all the multiple bit errors. In the GFP CORE HDR at the GFP-T receiver, these are uncorrectable.

gfpStatsRxTypeInvalid

Number of receive packets dropped due to Client Data Frame UPI errors.

gfpStatsRxCRCErrors

Number of packets received with a payload FCS error.

gfpStatsLFDRaised

Count of core HEC CRC multiple bit errors.

Note This count is only of eHec multiple bit errors when in frame. This can be looked at as a count of when the state machine goes out of frame.

gfpStatsCSFRaised

Number of GFP Client signal fail frames detected at the GFP-T receiver.

mediaIndStatsRxFrames
Truncated

Number of received frames that are too long. The maximum is the programmed maximum frame size (for VSAN support); if the maximum frame size is set to default, then the maximum is the 2112 byte payload plus the 36 byte header, which is a total of 2148 bytes.

mediaIndStatsRxFramesTooLong

Number of received frames with CRC error.s

mediaIndStatsRxShortPkts

Number of received packets that are too small.

gfpStatsRxSBitErrors

Sum of all the single bit errors. In the GFP CORE HDR at the GFP-T receiver, these are correctable.

gfpStatsRxMBitErrors

Sum of all the multiple bit errors. In the GFP CORE HDR at the GFP-T receiver, these are uncorrectable.

gfpStatsRxTypeInvalid

Number of receive packets dropped due to Client Data Frame UPI errors.

rprSpanStatsInUcastClassC
Frames

Number of received (PHY to MAC) classC unicast frames.

rprSpanStatsInUcastClassC
Octets

Number of received (PHY to MAC) classC unicast octets.

rprSpanStatsInMcastClassC
Frames

Number of received (PHY to MAC) classC multicast and broadcast frames.

rprSpanStatsInMcastClassC
Octets

Number of received (PHY to MAC) classC multicast and broadcast octets.

rprSpanStatsInUcastClassB
EirFrames

Number of received (PHY to MAC) classB EIR unicast frames.

rprSpanStatsInUcastClassB
EirOctets

Number of received (PHY to MAC) classB EIR unicast octets.

rprSpanStatsInMcastClassB
EirFrames

Number of received (PHY to MAC) classB EIR multicast and broadcast frames.

rprSpanStatsInMcastClassB
EirOctets

Number of received (PHY to MAC) classB EIR multicast and broadcast octets.

rprSpanStatsInUcastClassB
CirFrames

Number of received (PHY to MAC) classB CIR unicast frames.

rprSpanStatsInUcastClassB
CirOctets

Number of received (PHY to MAC) classB CIR unicast octets.

rprSpanStatsInMcastClassB
CirFrames

Number of received (PHY to MAC) classB CIR multicast and broadcast frames.

rprSpanStatsInMcastClassB
CirOctets

Number of received (PHY to MAC) classB CIR multicast and broadcast octets.

rprSpanStatsInUcastClassA
Frames

Number of received (PHY to MAC) classA unicast frames.

rprSpanStatsInUcastClassA
Octets

Number of received (PHY to MAC) classA unicast octets.

rprSpanStatsInMcastClassA
Frames

Number of received (PHY to MAC) classA multicast and broadcast frames.

rprSpanStatsInMcastClassA
Octets

Number of received (PHY to MAC) classA multicast and broadcast octets.

rprSpanStatsInCtrlFrames

Number of received (PHY to MAC) control frames processed by this MAC. This does not include control frames in transit, i.e. a multicast control frame received from a ringlet will be counted as In but not Out. This does not include Fairness or idle frames.

rprSpanStatsInOamEcho
Frames

Number of received (PHY to MAC) OAM echo frames processed by this MAC.

rprSpanStatsInOamFlush
Frames

Number of received (PHY to MAC) OAM flush frames processed by this MAC.

rprSpanStatsInOamOrgFrames

Number of received (PHY to MAC) OAM Org frames processed by this MAC.

rprSpanStatsInTopoAtdFrames

Number of received (PHY to MAC) Topology ATD frames processed by this MAC.

rprSpanStatsInTopoChkSum
Frames

Number of received (PHY to MAC) topology

checksum frames processed by this MAC.

rprSpanStatsInTopoTpFrames

Number of received (PHY to MAC) topology TP frames processed by this MAC.

rprSpanStatsOutUcastClassC
Frames

Number of transmitted (MAC to PHY) classC unicast frames.

rprSpanStatsOutUcastClassC
Octets

Number of transmitted (MAC to PHY) classC unicast octets.

rprSpanStatsOutMcastClassC
Frames

Number of transmitted (MAC to PHY) classC multicast and broadcast frames.

rprSpanStatsOutMcastClassC
Octets

Number of transmitted (MAC to PHY) classC multicast and broadcast octets.

rprSpanStatsOutUcastClassB
EirFrames

Number of transmitted (MAC to PHY) classB EIR unicast frames

rprSpanStatsOutUcastClassB
EirOctets

The number of transmitted (MAC to PHY) classB EIR unicast octets.

rprSpanStatsOutMcastClassB
EirFrames

The number of transmitted (MAC to PHY) classB EIR multicast and broadcast frames.

rprSpanStatsOutMcastClassB
EirOctets

The number of transmitted (MAC to PHY) classB EIR multicast and broadcast octets.

rprSpanStatsOutUcastClassB
CirFrames

The number of transmitted (MAC to PHY) classB CIR unicast frames.

rprSpanStatsOutUcastClassB
CirOctets

The number of transmitted (MAC to PHY) classB CIR unicast octets.

rprSpanStatsOutMcastClassB
CirFrames

The number of transmitted (MAC to PHY) classB CIR multicast and broadcast frames.

rprSpanStatsOutMcastClassB
CirOctets

The number of transmitted (MAC to PHY) classB CIR multicast and broadcast octets.

rprSpanStatsOutUcastClassA
Frames

The number of transmitted (MAC to PHY) classA unicast frames.

rprSpanStatsOutUcastClassA
Octets

The number of transmitted (MAC to PHY) classA unicast octets.

rprSpanStatsOutMcastClassA
Frames

The number of transmitted (MAC to PHY) classA multicast and broadcast frames.

rprSpanStatsOutMcastClassA
Octets

The number of transmitted (MAC to PHY) classA multicast and broadcast octets.

rprSpanStatsOutCtrlFrames

The number of transmitted (MAC to PHY) control frames generated by this MAC. This does not include control frames in transit, i.e. a multicast control frame received from a ringlet will be counted as In but not Out. This does not include Fairness or idle frames.

rprSpanStatsOutOamEcho
Frames

The number of transmitted (MAC to PHY) OAM echo frames generated by this MAC.

rprSpanStatsOutOamFlush
Frames

The number of transmitted (MAC to PHY) OAM flush frames generated by this MAC.

rprSpanStatsOutOamOrg
Frames

The number of transmitted (MAC to PHY) OAM Org frames generated by this MAC.

rprSpanStatsOutTopoAtd
Frames

The number of transmitted (MAC to PHY) topology ATD frames generated by this MAC.

rprSpanStatsOutTopoChkSum
Frames

The number of transmitted (MAC to PHY) topology checksum frames generated by this MAC.

rprSpanStatsOutTopoTp
Frames

The number of transmitted (MAC to PHY) topology TP frames generated by this MAC.

rprClientStatsInUcastClassC
Frames

The number of MAC to client classC unicast frames.

rprClientStatsInUcastClassC
Octets

The number of MAC to client classC unicast octets.

rprClientStatsInMcastClassC
Frames

The number of MAC to client classC multicast and broadcast frames.

rprClientStatsInMcastClassC
Octets

The number of MAC to client classC multicast and broadcast octets.

rprClientStatsInUcastClassB
EirFrames

The number of MAC to client classB EIR unicast frames.

rprClientStatsInUcastClassB
EirOctets

Number of packets received with a payload FCS error.

rprClientStatsInMcastClassB
EirFrames

Number of MAC to client classB EIR multicast and broadcast frames

rprClientStatsInMcastClassB
EirOctets

Number of MAC to client classB EIR multicast and broadcast octets.

rprClientStatsInUcastClassB
CirFrames

Number of MAC to client classB CIR unicast frames.

rprClientStatsInUcastClassB
CirOctets

Number of MAC to client classB CIR unicast octets.

rprClientStatsInMcastClassB
CirFrames

Number of MAC to client classB CIR multicast and broadcast frames.

rprClientStatsInMcastClassB
CirOctets

Number of MAC to client classB CIR multicast and broadcast octets

rprClientStatsInUcastClassA
Frames

Number of MAC to client classA unicast frames.

rprClientStatsInUcastClassA
Octets

Number of MAC to client classA unicast octets.

rprClientStatsInMcastClassA
Frames

Number of MAC to client classA multicast and broadcast frames.

rprClientStatsInMcastClassA
Octets

Number of MAC to client classA multicast and broadcast octets.

rprClientStatsInBcastFrames

Number of MAC to client broadcast frames. This is used only when deriving the multicast and broadcast packet counters for the interface MIB.

rprClientStatsOutUcastClassC
Frames

Number of client to MAC classC unicast frames.

rprClientStatsOutUcastClassC
Octets

Number of client to MAC classC unicast octets.

rprClientStatsOutMcastClassC
Frames

Number of client to MAC classC multicast and broadcast frames.

rprClientStatsOutMcastClassC
Octets

Number of client to MAC classC multicast and broadcast

octets.

rprClientStatsOutUcastClassB
EirFrames

Number of client to MAC classB EIR unicast

frames.

rprClientStatsOutUcastClassBEirOctets

Number of client to MAC classB EIR unicast

octets.

rprClientStatsOutMcastClassBEirFrames

Number of client to MAC classB EIR multicast and broadcast frames.

rprClientStatsOutMcastClassBEirOctets

Number of client to MAC classB EIR multicast and broadcast octets.

rprClientStatsOutUcastClassBCirFrames

Number of client to MAC classB CIR unicast frames.

rprClientStatsOutUcastClassBCirOctets

Number of client to MAC classB CIR unicast octets.

rprClientStatsOutMcastClassBCirFrames

Number of client to MAC classB CIR multicast and broadcast frames.

rprClientStatsOutMcastClassBCirOctets

Number of client to MAC classB CIR multicast and broadcast octets.

rprClientStatsOutUcastClassAFrames

Number of client to MAC classA unicast frames.

rprClientStatsOutUcastClassAOctets

Number of client to MAC classA unicast octets.

rprClientStatsOutMcastClassAFrames

Number of client to MAC classA multicast and broadcast frames.

rprClientStatsOutMcastClassAOctets

Number of client to MAC classA multicast and broadcast octets.

rprClientStatsOutBcastFrames

Number of client to MAC broadcast frames. This is used only when deriving the multicast and broadcast packet counters for the interface MIB.

rprErrorStatsBadParityFrames

Number of received (PHY to MAC) frames parity value not matching the expected parity value

rprErrorStatsBadHecFrames

The number of received (PHY to MAC) frames with HEC error

rprErrorStatsTtlExpFrames

The number of received (PHY to MAC) frames that were dropped due to zero Time To Live (TTL).

rprErrorStatsTooLongFrames

The number of received (PHY to MAC) frames that exceed the maximum permitted frame size.

rprErrorStatsTooShortFrames

The number of received (PHY to MAC) frames shortest than the minimum permitted frame size.

rprErrorStatsBadFcsFrames

The number of received (PHY to MAC) data and control frames where the fcs value did not match the expected fcs value.

rprErrorStatsSelfSrcUcastFrames

The number of received (PHY to MAC) unicast frames that were transmitted by the station itself. That is, the source MAC is equal to the interface MAC.

rprErrorStatsPmdAbortFrames

The number of received (PHY to MAC) frames that were aborted by the PMD.

rprErrorStatsBadAddrFrames

The number of received (PHY to MAC) frames with invalid SA value.

rprErrorStatsContainedFrames

The number of received (PHY to MAC) frames that were removed due to context containment.

rprErrorStatsScffErrors

The number of received (PHY to MAC) errored SCFF, with bad parity, bad FCS, or both.

gpfStatsCSFRaised

The number of total received client management frames.

gfpStatsLFDRaised

The number of Core HEC CRC Multiple Bit Errors.

Note This count is only for cHEC multiple bit error when in frame. It is a count of when the state machine goes out of frame.

rprPortCounterError

Packets dropped internally by the network processor.

Time Last Cleared

A time stamp indicating the last time statistics were reset.

Link Status

Indicates whether the Ethernet link is receiving a valid Ethernet signal (carrier) from the attached Ethernet device; up means present, and down means not present.

ifInOctets

Number of bytes received since the last counter reset.

rxTotalPkts

Number of received packets.

ifInUcastPkts

Number of unicast packets received since the last counter reset.

ifInMulticastPkts

Number of multicast packets received since the last counter reset.

ifInBroadcastPkts

Number of broadcast packets received since the last counter reset.

ifInDiscards

The number of inbound packets that were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free buffer space.

ifInErrors

The number of inbound packets (or transmission units) that contained errors preventing them from being deliverable to a higher-layer protocol.

ifOutOctets

Number of bytes transmitted since the last counter reset.

txTotalPkts

Number of transmitted packets.

ifOutDiscards¹

Number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their transmission. A possible reason for discarding such packets could be to free up buffer space.

ifOutErrors¹

Number of outbound packets or transmission units that could not be transmitted because of errors.

ifOutUcastPkts²

Number of unicast packets transmitted.

ifOutMulticastPkts²

Number of multicast packets transmitted.

ifOutBroadcastPkts²

Number of broadcast packets transmitted.

dot3StatsAlignment
Errors²

A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check.

dot3StatsFCSErrors

A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check.

dot3StatsSingleCollisionFrames²

A count of successfully transmitted frames on a particular interface for which transmission is inhibited by exactly on collision.

dot3StatsFrameTooLong

A count of frames received on a particular interface that exceed the maximum permitted frame size.

etherStatsUndersizePkts

The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.

etherStatsFragments

The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

Note It is entirely normal for etherStatsFragments to increment. This is because it counts both runts (which are normal occurrences due to collisions) and noise hits.

etherStatsPkts64Octets

The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).

etherStatsPkts65to127
Octets

The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts128to255
Octets

The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts256to511
Octets

The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts512to1023Octets

The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsPkts1024to1518Octets

The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).

etherStatsBroadcastPkts

The total number of good packets received that were directed to the broadcast address. Note that this does not include multicast packets.

etherStatsMulticastPkts

The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.

etherStatsOversizePkts

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. Note that for tagged interfaces, this number becomes 1522 bytes.

etherStatsJabbers

The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

etherStatsOctets

The total number of octets of data (including those in bad packets) received on the network (excluding framing bits but including FCS octets

etherStatsCollisions²

Number of transmit packets that are collisions; the port and the attached device transmitting at the same time caused collisions.

etherStatsCRCAlign
Errors²

The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but had either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a nonintegral number of octets (Alignment Error).

etherStatsDropEvents²

Number of received frames dropped at the port level.

rxPauseFrames¹

Number of received pause frames.

txPauseFrames¹

Number of transmitted pause frames.

rxPktsDroppedInternalCongestion¹

Number of received packets dropped due to overflow in frame buffer.

txPktsDroppedInternalCongestion¹

Number of transmit queue drops due to drops in frame buffer.

rxControlFrames¹

Number of received control frames.

mediaIndStatsRxFramesTruncated¹

Number of received frames with length of 36 bytes or less.

mediaIndStatsRxFramesTooLong¹

Number of received frames that are too long. The maximum is the programmed maximum frame size (for VSAN support); if the maximum frame size is set to default, then the maximum is the 2112 byte payload plus the 36 byte header, which is a total of 2148 bytes.

mediaIndStatsRxFramesBadCRC¹

Number of received frames with CRC error.

mediaIndStatsTxFramesBadCRC¹

Number of transmitted frames with CRC error.

mediaIndStatsRxShortPkts¹

Number of received packets that are too small.

¹ For CE1000-4 only

² For CE100T-8 only

Time Last Cleared

A time stamp indicating the last time that statistics were reset.

Link Status

Indicates whether the Ethernet link is receiving a valid Ethernet signal (carrier) from the attached Ethernet device; up means present, and down means not present.

ifInOctets

Number of bytes received since the last counter reset.

rxTotalPkts

Number of received packets.

ifInDiscards¹

The number of inbound packets that were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free buffer space.

ifInErrors¹

The number of inbound packets (or transmission units) that contained errors preventing them from being deliverable to a higher-layer protocol.

ifOutOctets

Number of bytes transmitted since the last counter reset.

txTotalPkts

Number of transmitted packets.

ifOutOversizePkts¹

Packets greater than 1518 bytes transmitted out a port.

gfpStatsRxFrame²

Number of received GFP frames.

gfpStatsTxFrame²

Number of transmitted GFP frames.

gfpStatsRxCRCErrors

Number of packets received with a payload FCS error.

gfpStatsRxOctets²

Number of GFP bytes received.

gfpStatsTxOctets²

Number of GFP bytes transmitted.

gfpStatsRxSBitErrors

Sum of all the single bit errors. In the GFP CORE HDR at the GFP-T receiver, these are correctable.

gfpStatsRxMBitErrors

Sum of all the multiple bit errors. In the GFP CORE HDR at the GFP-T receiver, these are uncorrectable.

gfpStatsRxTypeInvalid

Number of receive packets dropped due to Client Data Frame UPI errors.

gfpStatsRxCIDInvalid¹

Number of packets with invalid CID.

gfpStatsCSFRaised

Number of GFP Client signal fail frames detected at the GFP-T receiver.

ifInPayloadCrcErrors¹

Received payload CRC errors.

ifOutPayloadCrcErrors¹

Transmitted payload CRC errors.

hdlcPktDrops

Number of received packets dropped before input.

¹ Applicable only for CE100T-8,

² Applicable only for CE1000-4

CV-S
ES-S
SES-S
SEF-S

CV-L
ES-L
SES-L
UAS-L
FC-L
PSC (1+1)
PSD (1+1)

CV-P
ES-P
SES-P
UAS-P
FC-P
PPJC-PDET
NPJC-PDET
PPJC-PGEN
NPJC-PGEN
PPJC-PDET-P
PPJC-PGEN-P
PJC-DIFF

CV-LFE
ES-LFE
SES-LFE
UAS-LFE
FC-LFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

¹ The STS Path (FE) PMs are valid only for the OC3-4 card on ONS 15454. Also, OC-3/12/48 on 15310MA platform, MRC-12, and OC192/STM64-XFP based cards support far-end path PM parameters. All other optical cards do not support far-end path PM parameters.

CV-S
ES-S
SES-S
SEF-S

CV-L
ES-L
SES-L
UAS-L
FC-L
PSC (1+1)
PSD (1+1)

LBCL
OPT
OPR

CV-P
ES-P
SES-P
UAS-P
FC-P
PPJC-PDET-P
NPJC-PDET-P
PPJC-PGEN-P
NPJC-PGEN-P
PJCS-PDET-P
PJCS-PGEN-P
PJC-DIFF-P

CV-LFE
ES-LFE
SES-LFE
UAS-LFE
FC-LFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

CV-S
ES-S
SES-S
SEF-S

CV-L
ES-L
SES--L
UASL
FC-L
PSC (1+1, 2F BLSR)
PSD (1+1, 2F BLSR)
PSC-W (4F BLSR)
PSD-W (4F BLSR)
PSC-S (4F BLSR)
PSD-S (4F BLSR)
PSC-R (4F BLSR)
PSD-R (4F BLSR)

CV-P
ES-P
SES-P
UAS-P
FC-P
PPJC-PDET-P
NPJC-PDET-P
PPJC-PGEN-P
NPJC-PGEN-P
PJCS-PGEN-P
PJCS-PDET-P
PJC-DIFF-P

CV-L
ES-L
SES-L
UAS-L
FC-L

OC3

154-164

OC12

615-625

OC48

2459-2470

OC192

9835-9845

CV-S
ES-S
SES-S
SEF-S

CV-L
ES-L
SES-L
UAS-L
FC-L
PSC (1+1)
PSD (1+1)

LBC
OPT
OPR

CV-P
ES-P
SES-P
UAS-P
FC-P
PPJC-PDET-P
NPJC-PDET-P
PPJC-PGEN-P
NPJC-PGEN-P
PJCS-PDET-P
PJCS-PGEN-P
PJC-DIFF-P

CV-LFE
ES-LFE
SES-LFE
UAS-LFE
FC-LFE

CV-PFE
ES-PFE
SES-PFE
UAS-PFE
FC-PFE

Time Last Cleared

Time stamp indicating the time at which the statistics were last reset.

Link Status

Indicates whether the Fibre Channel link is receiving a valid Fibre Channel signal (carrier) from the attached Fibre Channel device; up means present, and down means not present.

ifInOctets

Number of bytes received without error for the Fibre Channel payload.

rxTotalPkts

Number of Fibre Channel frames received without errors.

ifInDiscards

Number of inbound packets that were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.

ifInErrors

Sum of frames that are oversized, undersized, or with cyclic redundancy check (CRC) error.

ifOutOctets

Number of bytes transmitted without error for the Fibre Channel payload.

txTotalPkts

Number of Fibre Channel frames transmitted without errors.

ifOutDiscards

Number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their transmission. A possible reason for discarding such packets could be to free up buffer space.

gfpStatsRxSBitErrors

Number of single bit errors in core header error check (CHEC).

gfpStatsRxMBitErrors

Number of multiple bit errors in CHEC.

gfpStatsRxTypeInvalid

Number of invalid generic framing procedure (GFP) type field received. This includes unexpected user payload identifier (UPI) type and also errors in CHEC.

gfpStatsRxSblkCRCErrors

Number of super block CRC errors.

gfpStatsRoundTripLatencyUSec

Round trip delay for the end-to-end Fibre Channel transport in milli seconds.

gfpStatsRxDistanceExtBuffers

Number of buffer credit received for GFP-T receiver (valid only if distance extension is enabled).

gfpStatsTxDistanceExtBuffers

Number of buffer credit transmitted for GFP-T transmitter (valid only if distance extension is enabled).

mediaIndStatsRxFramesTruncated

Number of Fibre Channel frames received with frame size <= 36 bytes.

mediaIndStatsRxFramesTooLong

Number of Fibre Channel frames received with frame size higher than the provisioned maximum frame size.

mediaIndStatsRxFramesBadCRC

Number of Fibre Channel frames received with bad CRC.

mediaIndStatsTxFramesBadCRC

Number of Fibre Channel frames transmitted with bad CRC.

fcStatsLinkRecoveries

Number of link recoveries.

fcStatsRxCredits

Number of buffers received to buffer credits T (valid only if distance extension is enable).

fcStatsTxCredits

Number of buffers transmitted to buffer credits T (valid only if distance extension is enable).

fcStatsZeroTxCredits

Number of transmit attempts that failed because of unavailable credits.

8b10bInvalidOrderedSets

8b10b loss of sync count on Fibre Channel line side.

8b10bStatsEncodingDispErrors

8b10b disparity violations count on Fibre Channel line side.

gfpStatsCSFRaised

Number of GFP Client Signal Fail frames detected.

STS-24

850000000

STS-48

850000000 x 2¹

¹ For 1 Gbps of bit rate being transported, there are only 850 Mbps of actual data because of 8b->10b conversion. Similarly, for 2 Gbps of bit rate being transported, there are only 1700 Mbps (850 Mbps x 2) of actual data.

1 minute

60 previous time intervals

15 minutes

32 previous time intervals

1 hour

24 previous time intervals

1 day (24 hours)

7 previous time intervals