Configuring IRB

This chapter describes how to configure integrated routing and bridging (IRB) for the ML-Series card. For more information about the Cisco IOS commands used in this chapter, refer to the Cisco IOS Command  Reference publication.

This chapter includes the following major sections:

•Understanding Integrated Routing and Bridging

•Configuring IRB

•Monitoring and Verifying IRB

Caution Cisco Inter-Switch Link (ISL) and Cisco Dynamic Trunking Protocol (DTP) are not supported by the ML-Series, but the ML-Series broadcast forwards these formats. Using ISL or DTP on connecting devices is not recommended. Some Cisco devices attempt to use ISL or DTP by default.

Understanding Integrated Routing and Bridging

Your network might require you to bridge local traffic within several segments and have hosts on the bridged segments reach the hosts or ML-Series card on routed networks. For example, if you are migrating bridged topologies into routed topologies, you might want to start by connecting some of the bridged segments to the routed networks.

Using the integrated routing and bridging (IRB) feature, you can route a given protocol between routed interfaces and bridge groups within a single ML-Series card. Specifically, local or unroutable traffic is bridged among the bridged interfaces in the same bridge group, while routable traffic is routed to other routed interfaces or bridge groups.

Because bridging is in the data link layer and routing is in the network layer, they have different protocol configuration models. With IP, for example, bridge group interfaces belong to the same network and have a collective IP network address. In contrast, each routed interface represents a distinct network and has its own IP network address. Integrated routing and bridging uses the concept of a Bridge Group Virtual Interface (BVI) to enable these interfaces to exchange packets for a given protocol.

A BVI is a virtual interface within the ML-Series card that acts like a normal routed interface. A BVI does not support bridging but actually represents the corresponding bridge group to routed interfaces within the ML-Series card. The interface number is the link between the BVI and the bridge group.

Before configuring IRB, consider the following:

•The default routing/bridging behavior in a bridge group (when IRB is enabled) is to bridge all packets. Make sure that you explicitly configure routing on the BVI for IP traffic.

•Packets of unroutable protocols such as local-area transport (LAT) are always bridged. You cannot disable bridging for the unroutable traffic.

•Protocol attributes should not be configured on the bridged interfaces when you are using IRB to bridge and route a given protocol. You can configure protocol attributes on the BVI, but you cannot configure bridging attributes on the BVI.

•A bridge links several network segments into one large, flat network. To bridge a packet coming from a routed interface among bridged interfaces, the bridge group should be represented by one interface.

•All ports in a BVI group must have matching MTU settings.

Configuring IRB

The process of configuring integrated routing and bridging consists of the following tasks:

1. Configure bridge groups and routed interfaces.

a. Enable bridging.

b. Assign interfaces to the bridge groups.

c. Configure the routing.

2. Enable IRB.

3. Configure the BVI.

a. Enable the BVI to accept routed packets.

b. Enable routing on the BVI.

4. Configure IP addresses on the routed interfaces.

5. Verify the IRB configuration.

When you configure the BVI and enable routing on it, packets that come in on a routed interface destined for a host on a segment that is in a bridge group are routed to the BVI and forwarded to the bridging engine. From the bridging engine, the packet exits through a bridged interface. Similarly, packets that come in on a bridged interface but are destined for a host on a routed interface go first to the BVI. The BVI forwards the packets to the routing engine that sends them out on the routed interface.

To configure a bridge group and an interface in the bridge group, perform the following procedure, beginning in global configuration mode:

 
Command
Purpose

Step 1  

Router(config)# bridge bridge-group 
protocol {ieee | rstp}

Defines one or more bridge groups.

Step 2  

Router(config)# interface type number

Enters interface configuration mode.

Step 3  

Router(config-if)# bridge-group 
bridge-group

Assigns the interface to the specified bridge group.

Step 4  

Router(config-if)# end

Returns to privileged EXEC mode.

To enable and configure IRB and BVI, perform the following procedure, beginning in global configuration mode:

 
Command
Purpose

Step 1  

Router(config)# bridge irb

Enables IRB. Allows bridging of traffic.

Step 2  

Router(config)# interface bvi bridge-group

Configures the BVI by assigning the number of the corresponding bridge group to the BVI. Each bridge group can have only one corresponding BVI.

Step 3  

Router(config-if)# ip address ip-address 
ip-address-subnet-mask

Configures IP addresses on routed interfaces.

Step 4  

Router(config-if)# exit

Exits the interface configuration mode.

Step 5  

Router(config)# bridge bridge-group route 
protocol

Enables a BVI to accept and route routable packets received from its corresponding bridge group.

Enter this command for each protocol that you want the BVI to route from its corresponding bridge group to other routed interfaces.

Step 6  

Router(config)# end

Returns to the privileged EXEC mode.

Step 7  

Router# copy running-config startup-config

(Optional) Saves your configuration changes to NVRAM.

Configuring IRB

Example 11-1 Configuring IRB

Example 11-2 Configuring Router A 

bridge irb

bridge 1 protocol ieee

 bridge 1 route ip

!

!

interface FastEthernet0

 ip address 192.168.2.1 255.255.255.0

!

interface POS0

 no ip address

 crc 32

bridge-group 1

 pos flag c2 1

!

interface POS1

 no ip address

 crc 32

bridge-group 1

 pos flag c2 1

!

interface BVI1

 ip address 192.168.1.1 255.255.255.0

!

router ospf 1

 log-adjacency-changes

 network 192.168.1.0 0.0.0.255 area 0

 network 192.168.2.0 0.0.0.255 area 0

Example 11-3 Configuring Router B 

bridge irb

bridge 1 protocol ieee

 bridge 1 route ip

!

!

interface FastEthernet0

 ip address 192.168.3.1 255.255.255.0

!

interface POS0

 no ip address

 crc 32

bridge-group 1

 pos flag c2 1

!

interface POS1

 no ip address

 crc 32

bridge-group 1

 pos flag c2 1

!

interface BVI1

 ip address 192.168.1.2 255.255.255.0

!

router ospf 1

 log-adjacency-changes

 network 192.168.1.0 0.0.0.255 area 0

 network 192.168.3.0 0.0.0.255 area 0

Monitoring and Verifying IRB

Table 11-1 shows the privileged EXEC commands for monitoring and verifying IRB.

Table 11-1 Commands for Monitoring and Verifying IRB

Command
Purpose 
Router# show interfaces bvi bridge-group

Shows BVI information, such as the BVI MAC address and processing statistics. 

Router# show interfaces [type-number] irb

Shows BVI information for the following:

•Protocols that this bridged interface can route to the other routed interface (if this packet is routable).

•Protocols that this bridged interface bridges


The following is sample output from the show interfaces bvi and show interfaces irb commands:

Example 11-4 Monitoring and Verifying IRB 

Router# show interfaces bvi1

BVI1 is up, line protocol is up

  Hardware is BVI, address is 0011.2130.b340 (bia 0000.0000.0000)

  Internet address is 100.100.100.1/24

  MTU 1500 bytes, BW 145152 Kbit, DLY 5000 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 03:35:28, output never, output hang never

  Last clearing of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/0 (size/max)

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     0 packets input, 0 bytes, 0 no buffer

     Received 0 broadcasts (0 IP multicast)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     1353 packets output, 127539 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 output buffer failures, 0 output buffers swapped out


Router# show interfaces irb

BVI1

Software MAC address filter on BVI1

  Hash Len    Address      Matches  Act      Type

  0x00:  0 ffff.ffff.ffff         0 RCV Physical broadcast

GigabitEthernet0

Bridged protocols on GigabitEthernet0:

  clns       ip

Software MAC address filter on GigabitEthernet0

  Hash Len    Address      Matches  Act      Type

  0x00:  0 ffff.ffff.ffff         0 RCV Physical broadcast

  0x58:  0 0100.5e00.0006         0 RCV IP multicast

  0x5B:  0 0100.5e00.0005         0 RCV IP multicast

  0x65:  0 0011.2130.b344         0 RCV Interface MAC address

  0xC0:  0 0100.0ccc.cccc         0 RCV CDP

  0xC2:  0 0180.c200.0000         0 RCV IEEE spanning tree

POS0

Routed protocols on POS0:

  ip

Bridged protocols on POS0:

  clns       ip

Software MAC address filter on POS0

  Hash Len    Address      Matches  Act      Type

  0x00:  0 ffff.ffff.ffff         9 RCV Physical broadcast

  0x58:  0 0100.5e00.0006         0 RCV IP multicast

  0x5B:  0 0100.5e00.0005      1313 RCV IP multicast

  0x61:  0 0011.2130.b340        38 RCV Interface MAC address

  0x61:  1 0011.2130.b340         0 RCV Bridge-group Virtual Interface

  0x65:  0 0011.2130.b344         0 RCV Interface MAC address

  0xC0:  0 0100.0ccc.cccc       224 RCV CDP

  0xC2:  0 0180.c200.0000         0 RCV IEEE spanning tree

POS1

SPR1

Bridged protocols on SPR1:

  clns       ip

Software MAC address filter on SPR1

  Hash Len    Address      Matches  Act      Type

  0x00:  0 ffff.ffff.ffff         0 RCV Physical broadcast

  0x60:  0 0011.2130.b341         0 RCV Interface MAC address

  0x65:  0 0011.2130.b344         0 RCV Interface MAC address

  0xC0:  0 0100.0ccc.cccc         0 RCV CDP

  0xC2:  0 0180.c200.0000         0 RCV IEEE spanning tree

Table 11-1 describes significant fields shown in the display.

Table 11-2 show interfaces irb Field Descriptions

Field
Description 
Routed protocols on...

List of the routed protocols configured for the specified interface. 

Bridged protocols on...

List of the bridged protocols configured for the specified interface.

Software MAC address filter on...

Table of software MAC address filter information for the specified interface. 

Hash

Hash key/relative position in the keyed list for this MAC-address entry. 

Len

Length of this entry to the beginning element of this hash chain. 

Address

Canonical (Ethernet ordered) MAC address. 

Matches

Number of received packets matched to this MAC address. 

Routed protocols on...

List of the routed protocols configured for the specified interface. 

Bridged protocols on...

List of the bridged protocols configured for the specified interface.