为Polycom会议电话配置Catalyst交换机

Cat6500#show running-config 
 Building configuration...
Current configuration : 5869 bytes
!
version 12.1 
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname cat6500
!

boot system sup-bootflash:s72033-psv-mz.122-18.SXD6.bin


main-cpu
 auto-sync standard
ip subnet-zero
!
!
no ip finger
!
!
!
!
vlan 1
name DataVlan
!
vlan 2
name VoiceVlan
!
interface FastEthernet4/1
 no ip address 
 switchport
 switchport trunk encapsulation dot1q
 switchport trunk native vlan 1
 switchport trunk allowed vlan 1,2
 switchport mode trunk
 spanning-tree portfast

!--- Use PortFast only when you connect a single end station to a !--- Layer 2 access port. Otherwise, you create a network loop. !--- Refer to Using Portfast and Other Commands to Fix Workstation Startup !--- Connectivity Delays for more information on how to enable portfast.

!
interface FastEthernet4/2
 no ip address
 switchport
 switchport access vlan 2
 switchport mode access
 spanning-tree portfast

!--- Use PortFast only when you connect a single end station to a Layer 2 access port. Otherwise, you create a network loop.

!
interface FastEthernet4/3
 no ip address
 shutdown
!

!--- Output suppressed.

!
ip classless
no ip http server
!
!
!
line con 0
transport input none
line vty 0 4 
!
end

!--- Set the VLAN Trunk Protocol (VTP) mode. !--- In this example, the mode is set to transparent. !--- Dependent upon your network, set the VTP mode accordingly. !--- Refer to Understanding and Configuring VLAN Trunk Protocol (VTP) !--- for more information on VTP.

Catalyst6500> (enable) set vtp mode transparent
VTP domain modified


!--- Add VLAN 2. VLAN 1 already exists by default.
 
Catalyst6500> (enable) set vlan 2
VLAN 2 configuration successful


!--- Add port 4/2 to VLAN 2.

Catalyst6500> (enable) set vlan 2 4/2
VLAN 2 modified.
VLAN 1 modified.
VLAN  Mod/Ports
---- -----------------------
2     4/2


!--- Enable trunking on port 4/1.

Catalyst6500> (enable) set trunk 4/1 1,2 dot1q on
Vlan(s) 1,2 already allowed on the trunk
Please use the 'clear trunk' command to remove vlans from allowed list.
Port(s)  4/1 trunk mode set to on.
Port(s)  4/1 trunk type set to dot1q.
Catalyst6500> (enable) 


!--- Enable spanning tree portfast on the ports. Refer to !--- Using Portfast and Other Commands to Fix Workstation Startup Connectivity Delays !--- for more information on how to enable portfast.

Catalyst6500> (enable) set spantree portfast 4/1 enable

Warning: Connecting Layer 2 devices to a fast start port can cause
temporary spanning tree loops. Use with caution.

Spantree port  4/1 fast start enabled.
Catalyst6500> (enable) set spantree portfast 4/2 enable

Warning: Connecting Layer 2 devices to a fast start port can cause
temporary spanning tree loops. Use with caution.

Spantree port  4/2 fast start enabled.
Catalyst6500> (enable)


!--- If you want to ONLY allow VLAN 1 and VLAN 2 on trunk port 4/1, do this. !--- A trunk port allows all VLANs by default.

Catalyst6500> (enable) show trunk 4/1
* - indicates vtp domain mismatch
# - indicates dot1q-all-tagged enabled on the port
$ - indicates non-default dot1q-ethertype value
Port      Mode         Encapsulation  Status        Native vlan
--------  -----------  -------------  ------------  -----------
 4/1      on           dot1q          not-trunking  1

Port      Vlans allowed on trunk
--------  ---------------------------------------------------------------------
 4/1      1-4094

Port      Vlans allowed and active in management domain 
--------  ---------------------------------------------------------------------
 4/1      1

Port      Vlans in spanning tree forwarding state and not pruned
--------  ---------------------------------------------------------------------
 4/1       
Catalyst6500> (enable) clear trunk 4/1 1-4094
Removing Vlan(s) 1-4094 from allowed list.
Port  4/1 allowed vlans modified to none.


!--- Allow only VLAN 1 and VLAN 2 on trunk port 4/1.

Catalyst6500> (enable) set trunk 4/1 1,2 dot1q on
Adding vlans 1,2 to allowed list.
Port(s)  4/1 allowed vlans modified to 1,2.
Port(s)  4/1 trunk mode set to on.
Port(s)  4/1 trunk type set to dot1q.

Catalyst6500> (enable) show trunk 4/1
* - indicates vtp domain mismatch
# - indicates dot1q-all-tagged enabled on the port
$ - indicates non-default dot1q-ethertype value
Port      Mode         Encapsulation  Status        Native vlan
--------  -----------  -------------  ------------  -----------
 4/1      on           dot1q          not-trunking  1

Port      Vlans allowed on trunk
--------  ---------------------------------------------------------------------
 4/1      1,2

Port      Vlans allowed and active in management domain 
--------  ---------------------------------------------------------------------
 4/1      1

Port      Vlans in spanning tree forwarding state and not pruned
--------  ---------------------------------------------------------------------
 4/1       

!--- Refer to Configuring Ethernet VLAN Trunks for more !--- information on how to configure trunk ports. 


!--- Issue the show config 
            command !--- in order to check the configuration.

Catalyst6500> (enable) show config 4
This command shows non-default configurations only.
Use 'show config <mod> all' to show both default and non-default configurations.
.................................
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Thu Jun 21 2007, 23:37:51 
!
# default port status is enable
!
!
#module 4 : 16-port 1000BaseX Ethernet
set vlan 2    4/2
clear trunk 4/1  1-9,11-39,41-4094
set trunk 4/1  on dot1q 1,2
set spantree portfast    4/1-2 enable
end
Catalyst6500> (enable)