이 문서에서는 HUB ASA가 동일한 인터페이스에서 Site to Site Tunnel 및 Easy VPN IPsec Connections를 수락하는 방법에 대한 샘플 컨피그레이션을 제공합니다. Cisco ASA 5520과 Cisco ASA(Adaptive Security Appliance) 5505 사이의 IPsec은 NEM(Network Extension Mode)을 사용하는 Easy VPN을 사용합니다.
이 문서에 대한 특정 요건이 없습니다.
이 문서의 정보는 다음 소프트웨어 및 하드웨어 버전을 기반으로 합니다.
버전 7.x 이상을 실행하는 ASA 5500 Series(허브)
참고: HUB ASA 컨피그레이션은 버전 7.x 이상을 실행하는 PIX Security Appliance 515, 515E, 525 및 535와 함께 사용할 수도 있습니다.
버전 7.x 이상을 실행하는 Easy VPN ASA 5505
버전 7.x 이상을 실행하는 PIX Security Appliance 515, 515E, 525 및 535
이 문서의 정보는 특정 랩 환경의 디바이스를 토대로 작성되었습니다. 이 문서에 사용된 모든 디바이스는 초기화된(기본) 컨피그레이션으로 시작되었습니다. 현재 네트워크가 작동 중인 경우, 모든 명령어의 잠재적인 영향을 미리 숙지하시기 바랍니다.
문서 규칙에 대한 자세한 내용은 Cisco 기술 팁 규칙을 참조하십시오.
이 섹션에서는 이 문서에서 설명하는 기능을 구성하는 데 사용할 수 있는 정보를 제공합니다.
참고: 이 섹션에 사용된 명령에 대한 자세한 내용을 보려면 명령 조회 도구(등록된 고객만 해당)를 사용하십시오.
이 문서에서는 다음 네트워크 설정을 사용합니다.
참고: 이 구성에 사용된 IP 주소 지정 체계는 인터넷에서 합법적으로 라우팅할 수 없습니다. 실습 환경에서 사용되는 RFC 1918 주소입니다.
이 문서에서는 다음 구성을 사용합니다.
허브 ASA |
---|
ASA Version 8.0(2) ! hostname ciscoasa enable password 8Ry2YjIyt7RRXU24 encrypted names ! interface Ethernet0/0 nameif outside security-level 0 ip address 10.1.1.1 255.255.255.0 ! interface Ethernet0/1 nameif inside security-level 100 ip address 192.168.2.1 255.255.255.0 ! !--- Output Suppressed. !--- Access-list for interesting traffic (Site to Site) to be !--- encrypted between hub ASA and spoke (PIX) networks. access-list outside_cryptomap_20 extended permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0 !--- Access-list for interesting traffic to be !--- encrypted between hub ASA and spoke easy vpn client ASA networks. access-list ezvpn1 extended permit ip 192.168.2.0 255.255.255.0 192.168.3.0 255.255.255.0 !--- Access-list for traffic to bypass the network address !--- translation (NAT) process. access-list nonat extended permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0 access-list nonat extended permit ip 192.168.2.0 255.255.255.0 192.168.3.0 255.255.255.0 !--- Output Suppressed. !--- Specify the NAT configuration. !--- NAT 0 prevents NAT for the ACL defined in this configuration. !--- The nat 1 command specifies NAT for all other traffic. nat-control global (outside) 1 interface nat (inside) 0 access-list nonat nat (inside) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 10.1.1.2 1 !--- Output Suppressed. !--- Configuration of IPsec Phase 2 crypto ipsec transform-set myset esp-3des esp-sha-hmac !--- IPsec configuration for the dynamic LAN-to-LAN tunnel crypto dynamic-map ezvpn 30 set transform-set myset !--- IPsec configuration for the static LAN-to-LAN tunnel crypto map outside_map 20 match address outside_cryptomap_20 crypto map outside_map 20 set peer 172.16.1.1 crypto map outside_map 20 set transform-set myset !--- IPsec configuration that binds dynamic map to crypto map crypto map outside_map 65535 ipsec-isakmp dynamic ezvpn !--- Crypto map applied to the outside interface of the ASA crypto map outside_map interface outside isakmp enable outside !--- PHASE 1 CONFIGURATION ---! !--- This configuration uses isakmp policy 1. !--- These configuration commands !--- define the Phase 1 policies that are used. crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 !--- Output Suppressed. !--- This defines the group policy you use with Easy VPN. !--- Specify the networks that can pass through !--- the tunnel and that you want to !--- use network extension mode. group-policy tunnel internal group-policy tunnel attributes nem enable !--- The username and password associated with !--- this VPN connection are defined here. You !--- can also use AAA for this function. username cisco password ffIRPGpDSOJh9YLq encrypted tunnel-group 172.16.1.1 type ipsec-l2l tunnel-group 172.16.1.1 ipsec-attributes pre-shared-key * !--- The tunnel-group commands bind the configurations !--- defined in this configuration to the tunnel that is !--- used for Easy VPN. This tunnel name is the one !--- specified on the remote side. tunnel-group mytunnel type remote-access tunnel-group mytunnel general-attributes default-group-policy tunnel !--- Defines the pre-shared key used for !--- IKE authentication for the dynamic tunnel. tunnel-group mytunnel ipsec-attributes pre-shared-key * prompt hostname context Cryptochecksum:e148bf43d04906f5db41fc6f90c52d34 : end |
Easy VPN Client - ASA 5505 |
---|
ASA Version 7.2(2) ! hostname ciscoasa domain-name default.domain.invalid enable password 8Ry2YjIyt7RRXU24 encrypted names ! interface Vlan1 nameif outside security-level 0 ip address 172.16.2.2 255.255.255.0 ! interface Vlan2 nameif inside security-level 100 ip address 192.168.3.1 255.255.255.0 ! interface Ethernet0/0 ! interface Ethernet0/1 shutdown ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 2 !--- Output Suppressed. ! route outside 0.0.0.0 0.0.0.0 172.16.2.1 1 !--- Output Suppressed. !--- Easy VPN Client Configuration ---! !--- Specify the IP address of the VPN server. vpnclient server 10.1.1.1 !--- This example uses network extension mode. vpnclient mode network-extension-mode !--- Specify the group name and the pre-shared key. vpnclient vpngroup mytunnel password ******** !--- Specify the authentication username and password. vpnclient username cisco password ******** !--- In order to enable the device as hardware vpnclient, use this command. vpnclient enable ! !--- Output Suppressed. Cryptochecksum:0458ce7a08e6b7f9417b17bc254eb4e2 : end |
PIX |
---|
PIX Version 8.0(2) ! hostname pixfirewall enable password 8Ry2YjIyt7RRXU24 encrypted names ! interface Ethernet0 nameif outside security-level 0 ip address 172.16.1.1 255.255.255.0 ! interface Ethernet1 nameif inside security-level 100 ip address 192.168.1.2 255.255.255.0 ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive !--- This access list (inside_nat0_outbound) is used with the nat zero command. !--- This prevents traffic which matches the access list from undergoing !--- network address translation (NAT). access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 !--- The traffic specified by this ACL is !--- traffic that is to be encrypted and !--- sent across the VPN tunnel. This ACL is intentionally !--- the same as (inside_nat0_outbound). !--- Two separate access lists must always be used in this configuration. access-list outside_cryptomap_20 extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 !--- NAT 0 prevents NAT for networks specified in the ACL inside_nat0_outbound. nat (inside) 0 access-list inside_nat0_outbound !--- Output Suppressed. route outside 0.0.0.0 0.0.0.0 172.16.1.2 1 !--- Output Suppressed. !--- PHASE 2 CONFIGURATION ---! !--- The encryption types for Phase 2 are defined here. !--- Define the transform set for Phase 2. crypto ipsec transform-set myset esp-3des esp-sha-hmac !--- Define which traffic can be sent to the IPsec peer. crypto map outside_map 20 match address outside_cryptomap_20 !--- Sets the IPsec peer. crypto map outside_map 20 set peer 10.1.1.1 !--- Sets the IPsec transform set "myset" !--- to be used with the crypto map entry "outside_map". crypto map outside_map 20 set transform-set myset !--- Specifies the interface to be used with !--- the settings defined in this configuration. crypto map outside_map interface outside !--- PHASE 1 CONFIGURATION ---! !--- This configuration uses isakmp policy 10. !--- Policy 65535 is included in the config by default. !--- The configuration commands here define the Phase !--- 1 policy parameters that are used. crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 !--- Output Suppressed. !--- In order to create and manage the database of connection-specific records !--- for ipsec-l2l—IPsec (LAN-to-LAN) tunnels, use the tunnel-group !--- command in global configuration mode. !--- For L2L connections the name of the tunnel group MUST be the IP !--- address of the IPsec peer. tunnel-group 10.1.1.1 type ipsec-l2l !--- Enter the pre-shared-key in order to configure the authentication method. tunnel-group 10.1.1.1 ipsec-attributes pre-shared-key * prompt hostname context Cryptochecksum:4a2c70f2102113315de795f13f25c2aa : end |
이 섹션에서는 컨피그레이션이 제대로 작동하는지 확인하는 데 사용할 수 있는 정보를 제공합니다.
Output Interpreter 도구(등록된 고객만 해당)(OIT)는 특정 show 명령을 지원합니다. OIT를 사용하여 show 명령 출력의 분석을 봅니다.
show crypto isakmp sa - 피어의 현재 IKE SA(Security Association)를 모두 표시합니다.
show crypto ipsec sa - 현재 모든 SA를 표시합니다.
이 섹션에서는 다음에 대한 확인 구성의 예를 보여줍니다.
허브 ASA |
---|
ciscoasa #show crypto isakmp sa Active SA: 2 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey) Total IKE SA: 2 !--- Dynamic LAN-to-LAN tunnel establishment 1 IKE Peer: 172.16.2.2 Type : user Role : responder Rekey : no State : AM_ACTIVE !--- Static LAN-to-LAN tunnel establishment 2 IKE Peer: 172.16.1.1 Type : L2L Role : initiator Rekey : no State : MM_ACTIVE ciscoasa #show crypto ipsec sa ciscoasa(config)#sh crypto ipsec sa interface: outside Crypto map tag: outside_map, seq num: 20, local addr: 10.1.1.1 access-list outside_cryptomap_20 permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0 local ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0) current_peer: 172.16.1.1 #pkts encaps: 4, #pkts encrypt: 4, #pkts digest: 4 #pkts decaps: 4, #pkts decrypt: 4, #pkts verify: 4 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 4, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.1.1 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: E4312E13 inbound esp sas: spi: 0x9ABAC3DD (2595931101) transform: esp-3des esp-sha-hmac none in use settings ={L2L, Tunnel, } slot: 0, conn_id: 741376, crypto-map: outside_map sa timing: remaining key lifetime (kB/sec): (4274999/28783) IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0xE4312E13 (3828428307) transform: esp-3des esp-sha-hmac none in use settings ={L2L, Tunnel, } slot: 0, conn_id: 741376, crypto-map: outside_map sa timing: remaining key lifetime (kB/sec): (4274999/28783) IV size: 8 bytes replay detection support: Y Crypto map tag: ezvpn, seq num: 30, local addr: 10.1.1.1 local ident (addr/mask/prot/port): (10.1.1.1/255.255.255.255/0/0) remote ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0) current_peer: 172.16.2.2, username: cisco dynamic allocated peer ip: 0.0.0.0 #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.2.2 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: 2647B59C inbound esp sas: spi: 0x21685AF8 (560487160) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 737280, crypto-map: ezvpn sa timing: remaining key lifetime (sec): 28146 IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0x2647B59C (642233756) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 737280, crypto-map: ezvpn sa timing: remaining key lifetime (sec): 28146 IV size: 8 bytes replay detection support: Y Crypto map tag: ezvpn, seq num: 30, local addr: 10.1.1.1 local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0) remote ident (addr/mask/prot/port): (192.168.3.0/255.255.255.0/0/0) current_peer: 172.16.2.2, username: cisco dynamic allocated peer ip: 0.0.0.0 #pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5 #pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 5, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.2.2 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: 07997B21 inbound esp sas: spi: 0xB5B6013D (3048603965) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 737280, crypto-map: ezvpn sa timing: remaining key lifetime (sec): 28145 IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0x07997B21 (127499041) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 737280, crypto-map: ezvpn sa timing: remaining key lifetime (sec): 28145 IV size: 8 bytes replay detection support: Y Crypto map tag: ezvpn, seq num: 30, local addr: 10.1.1.1 local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0) remote ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0) current_peer: 172.16.2.2, username: cisco dynamic allocated peer ip: 0.0.0.0 #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 10.1.1.1, remote crypto endpt.: 172.16.2.2 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: 0F0B1A75 inbound esp sas: spi: 0x68B0EA75 (1756424821) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 737280, crypto-map: ezvpn sa timing: remaining key lifetime (sec): 28143 IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0x0F0B1A75 (252385909) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 737280, crypto-map: ezvpn sa timing: remaining key lifetime (sec): 28143 IV size: 8 bytes replay detection support: Y |
Easy VPN Client ASA 5505 |
---|
ciscoasa(config)# sh crypto isakmp sa Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey) Total IKE SA: 1 1 IKE Peer: 10.1.1.1 Type : user Role : initiator Rekey : no State : AM_ACTIVE ciscoasa(config)# sh crypto ipsec sa interface: outside Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.2.2 access-list _vpnc_acl permit ip host 172.16.2.2 host 10.1.1.1 local ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0) remote ident (addr/mask/prot/port): (10.1.1.1/255.255.255.255/0/0) current_peer: 10.1.1.1, username: 10.1.1.1 dynamic allocated peer ip: 0.0.0.0 #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 172.16.2.2, remote crypto endpt.: 10.1.1.1 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: 21685AF8 inbound esp sas: spi: 0x2647B59C (642233756) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 178, crypto-map: _vpnc_cm sa timing: remaining key lifetime (sec): 28298 IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0x21685AF8 (560487160) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 178, crypto-map: _vpnc_cm sa timing: remaining key lifetime (sec): 28298 IV size: 8 bytes replay detection support: Y Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.2.2 access-list _vpnc_acl permit ip host 172.16.2.2 any local ident (addr/mask/prot/port): (172.16.2.2/255.255.255.255/0/0) remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0) current_peer: 10.1.1.1, username: 10.1.1.1 dynamic allocated peer ip: 0.0.0.0 #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 172.16.2.2, remote crypto endpt.: 10.1.1.1 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: 68B0EA75 inbound esp sas: spi: 0x0F0B1A75 (252385909) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 178, crypto-map: _vpnc_cm sa timing: remaining key lifetime (sec): 28298 IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0x68B0EA75 (1756424821) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 178, crypto-map: _vpnc_cm sa timing: remaining key lifetime (sec): 28298 IV size: 8 bytes replay detection support: Y Crypto map tag: _vpnc_cm, seq num: 10, local addr: 172.16.2.2 access-list _vpnc_acl permit ip 192.168.3.0 255.255.255.0 any local ident (addr/mask/prot/port): (192.168.3.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0) current_peer: 10.1.1.1, username: 10.1.1.1 dynamic allocated peer ip: 0.0.0.0 #pkts encaps: 5, #pkts encrypt: 5, #pkts digest: 5 #pkts decaps: 5, #pkts decrypt: 5, #pkts verify: 5 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 172.16.2.2, remote crypto endpt.: 10.1.1.1 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: B5B6013D inbound esp sas: spi: 0x07997B21 (127499041) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 178, crypto-map: _vpnc_cm sa timing: remaining key lifetime (sec): 28294 IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0xB5B6013D (3048603965) transform: esp-3des esp-sha-hmac none in use settings ={RA, Tunnel, } slot: 0, conn_id: 178, crypto-map: _vpnc_cm sa timing: remaining key lifetime (sec): 28294 IV size: 8 bytes replay detection support: Y |
PIX |
---|
pixfirewall(config)# sh crypto isakmp sa Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey) Total IKE SA: 1 1 IKE Peer: 10.1.1.1 Type : L2L Role : responder Rekey : no State : MM_ACTIVE pixfirewall(config)# sh crypto ipsec sa interface: outside Crypto map tag: outside_map, seq num: 20, local addr: 172.16.1.1 access-list outside_cryptomap_20 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0) current_peer: 10.1.1.1 #pkts encaps: 4, #pkts encrypt: 4, #pkts digest: 4 #pkts decaps: 4, #pkts decrypt: 4, #pkts verify: 4 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0 local crypto endpt.: 172.16.1.1, remote crypto endpt.: 10.1.1.1 path mtu 1500, ipsec overhead 58, media mtu 1500 current outbound spi: 9ABAC3DD inbound esp sas: spi: 0xE4312E13 (3828428307) transform: esp-3des esp-sha-hmac none in use settings ={L2L, Tunnel, } slot: 0, conn_id: 12288, crypto-map: outside_map sa timing: remaining key lifetime (kB/sec): (3824999/28628) IV size: 8 bytes replay detection support: Y outbound esp sas: spi: 0x9ABAC3DD (2595931101) transform: esp-3des esp-sha-hmac none in use settings ={L2L, Tunnel, } slot: 0, conn_id: 12288, crypto-map: outside_map sa timing: remaining key lifetime (kB/sec): (3824999/28628) IV size: 8 bytes replay detection support: Y |
이 섹션에서는 컨피그레이션 문제를 해결하는 데 사용할 수 있는 정보를 제공합니다.
일부 show 명령은 출력 인터프리터 툴 에서 지원되는데(등록된 고객만), 이 툴을 사용하면 show 명령 출력의 분석 결과를 볼 수 있습니다.
참고: 디버그 명령을 실행하기 전에 디버그 명령에 대한 중요 정보를 참조하십시오.
구성 모드에서 PIX 명령을 실행합니다.
clear crypto isakmp sa - 1단계 SA를 지웁니다.
clear crypto ipsec sa - 2단계 SA를 지웁니다.
VPN 터널의 debug 명령:
debug crypto isakmp sa - ISAKMP SA 협상 디버깅
debug crypto ipsec sa - IPSec SA 협상 디버깅
개정 | 게시 날짜 | 의견 |
---|---|---|
1.0 |
30-Sep-2008 |
최초 릴리스 |