PGW 2200 の複数発信ポイント コードの設定例

!--- Two unique point codes are defined for the PGW 2200.

prov-add:OPC:NAME="opc-1",DESC="Originating Point Code 1",
NETADDR="10.20.1",NETIND=2,TYPE="TRUEOPC"
prov-add:OPC:NAME="opc-2",
DESC="Originating Point Code 2",NETADDR="10.20.2",NETIND=2,TYPE="TRUEOPC"

!--- Destination point codes are defined for the SSPs !--- that you connect to. For point code 20.20.1 there are duplicate entries. !--- Each one is associated to a different IOCC that represents each OPC. 



prov-add:DPC:NAME="dpc-simplex",DESC="Destination Point Code for BTS Simplex(650)",
NETADDR="20.20.1",NETIND=2
prov-add:DPC:NAME="dpc-simplex-opc2",DESC="Destination Point Code for BTS 
Simplex(650)from opc2",NETADDR="20.20.1",NETIND=2



!--- The SS7 variant is defined that is used between you and !--- the destination SSP.



prov-add:SS7PATH:NAME="ss7p-simplex",DESC="SS7 Signaling Service to 
BTS Simplex via opc-1",MDO="ANSISS7_STANDARD",CUSTGRPID="0000",SIDE="network",
DPC="dpc-simplex",OPC="opc-1"
prov-add:SS7PATH:NAME="ss7p-simplex-opc2",
DESC="SS7 Signaling Service to BTS Simplex via opc-2",MDO="ANSISS7_STANDARD",
CUSTGRPID="0000",SIDE="network",DPC="dpc-simplex-opc2",OPC="opc-2"
	


!--- The SLTs are defined and gateways that are part of !--- the PGW 2200 solution.

prov-add:EXTNODE:NAME="slt-1",DESC="SLT-1-2651XM",TYPE="SLT"
prov-add:EXTNODE:NAME="slt-2",DESC="SLT-2-2651XM",TYPE="SLT"prov-add:EXTNODE:
NAME="as5300-2",DESC="AS5300-2 Gateway",TYPE="AS5300"

!--- The RUDP connections are defined between !--- the PGW 2200 and the two SLTs. !--- Note that you need to define duplicate entries for the sessionset. !--- Each one is associated to a different IOCC that represents each OPC.


prov-add:SESSIONSET:NAME="sset-slt1",EXTNODE="slt-1",IPADDR1="IP_Addr1",
PEERADDR1="172.16.20.14",PORT=7000,PEERPORT=7000,NEXTHOP1="0.0.0.0",
NETMASK1="255.255.255.255",TYPE="BSMV0"
prov-add:SESSIONSET:NAME="sset-slt1-opc2",EXTNODE="slt-1",IPADDR1=
"IP_Addr1",PEERADDR1="172.16.20.14",PORT=7002,PEERPORT=7002,NEXTHOP1=
"0.0.0.0",NETMASK1="255.255.255.255",TYPE="BSMV0"
prov-add:SESSIONSET:NAME="sset-slt2",EXTNODE="slt-2",IPADDR1="IP_Addr1",
PEERADDR1="172.16.20.15",PORT=7000,PEERPORT=7000,NEXTHOP1="0.0.0.0",
NETMASK1="255.255.255.255",TYPE="BSMV0"
prov-add:SESSIONSET:NAME="sset-slt2-opc2",EXTNODE="slt-2",IPADDR1=
"IP_Addr1",PEERADDR1="172.16.20.15",PORT=7002,PEERPORT=7002,NEXTHOP1=
"0.0.0.0",NETMASK1="255.255.255.255",TYPE="BSMV0"
	 

!--- The point codes of the STPs are defined that you connect to. !--- Note that you need to define duplicate entries for the APCs. !--- Each one is associated to a different IOCC that represents each OPC.

	 
prov-add:APC:NAME="itp-1",DESC="Adjacent Point Code for ITP1(100-1-1)
",NETADDR="100.1.1",NETIND=2 
prov-add:APC:NAME="itp-2",DESC="Adjacent Point Code for ITP2 (100-1-2)
",NETADDR="100.1.2",NETIND=2
prov-add:APC:NAME="itp-1-opc2",DESC="Adjacent Point Code for ITP1 (100-1-1)
 for opc-2",NETADDR="100.1.1",NETIND=2 
prov-add:APC:NAME="itp-2-opc2",DESC="Adjacent Point Code for ITP2 (100-1-2)
 for opc-2",NETADDR="100.1.2",NETIND=2


!--- Define the SS7 links between the PGW 2200 and the STP. !--- You need to define duplicate entries for the LNKSET. !--- Each duplicate entry is associated to a different IOCC that !--- represents each OPC.


prov-add:LNKSET:NAME="lnkset-itp1",DESC="From 2651XM-1 Lnkset to ITP1
",APC="itp-1",PROTO="SS7-ANSI",TYPE="IP"
prov-add:LNKSET:NAME="lnkset-itp2
",DESC="From 2651XM-1 Lnkset to ITP2",APC="itp-2",PROTO="SS7-ANSI",TYPE=
"IP"
prov-add:LNKSET:NAME="lnkset-itp1-opc2",DESC="From 2651XM-1 Lnkset to 
ITP1 for opc-2",APC="itp-1-opc2",PROTO="SS7-ANSI",TYPE="IP"
prov-add:
LNKSET:NAME="lnkset-itp2-opc2",DESC="From 2651XM-1 Lnkset to ITP2 for 
opc-2",APC="itp-2-opc2",PROTO="SS7-ANSI",TYPE="IP"	 


!--- Define routes to the destination point code via each SLT. !--- Also, define the routes to the STPs. You need to !--- define duplicate entries for the SS7ROUTE. !--- Each duplicate entry is associated to a different !--- IOCC that represents each OPC.


prov-add:SS7ROUTE:NAME="ss7r-simplex-1",DESC="SS7 Route to BTS Simplex 
via ITP1",OPC="opc-1",DPC="dpc-simplex",LNKSET="lnkset-itp1", PRI=1
prov-add:SS7ROUTE:NAME="ss7r-simplex-2",DESC="SS7 Route to BTS Simplex 
via ITP2",OPC="opc-1",DPC="dpc-simplex",LNKSET="lnkset-itp2", PRI=1
prov-add:SS7ROUTE:NAME="ss7r-simplex-1-opc2",DESC="SS7 Route to BTS 
Simplex via ITP1 using opc-2",OPC="opc-2",DPC="dpc-simplex-opc2",
LNKSET="lnkset-itp1-opc2",PRI=1
prov-add:SS7ROUTE:NAME="ss7r-simplex-2-opc2",DESC="SS7 Route to 
BTS Simplex via ITP2 using opc-2",OPC="opc-2",DPC="dpc-simplex-opc2
",LNKSET="lnkset-itp2-opc2",PRI=1
prov-add:SS7ROUTE:NAME="ss7r-itp1-opc2",DESC="SS7 Route to ITP1 
via opc-2",OPC="opc-2",DPC="itp-1-opc2",LNKSET="lnkset-itp1-opc2",PR I=1
prov-add:SS7ROUTE:NAME="ss7r-itp2-opc2",DESC="SS7 Route to ITP2 via 
opc-2",OPC="opc-2",DPC="itp-2-opc2",LNKSET="lnkset-itp2-opc2",PR I=1
prov-add:SS7ROUTE:NAME="ss7r-itp1",DESC="SS7 Route to ITP1 via opc-1
",OPC="opc-1",DPC="itp-1",LNKSET="lnkset-itp1",PRI=1
prov-add:SS7ROUTE:NAME="ss7r-itp2",DESC="SS7 Route to ITP2 via opc-1
",OPC="opc-1",DPC="itp-2",LNKSET="lnkset-itp2",PRI=1 


!--- Define the IP link between the PGW 2200 and the SLT. !--- You need to create duplicate entries for the C7IPLNK. !--- Each duplicate entry is associated to a different !--- IOCC that represents each OPC.

	 
prov-add:C7IPLNK:NAME="c7ip-itp1-0",DESC="C7Iplink to ITP1 SLC 0 via 
SLT1",LNKSET="lnkset-itp1",SLC=0,PRI=1,TIMESLOT=0,SESSIONSET="s set-slt1"
prov-add:C7IPLNK:NAME="c7ip-itp2-1",DESC="C7Iplink to ITP2 SLC 1 via 
SLT2",LNKSET="lnkset-itp2",SLC=1,PRI=1,TIMESLOT=1,SESSIONSET=" sset-slt2"
prov-add:C7IPLNK:NAME="c7ip-itp1-1-opc2",DESC="C7Iplink to ITP1 SLC 1 
via SLT-2 for opc-2",LNKSET="lnkset-itp1-opc2",SLC=1,PRI=1,TIMESLOT=0,
SESSIONSET="sset-slt2-opc2"
prov-add:C7IPLNK:NAME="c7ip-itp2-0-opc2",DESC="C7Iplink to ITP2 SLC 0 
via SLT-1 for opc-2",LNKSET="lnkset-itp2-opc2",SLC=0,PRI=1,TIMESLOT=1,
SESSIONSET="sset-slt1-opc2"


!--- Define the SS7 Subsystems which allow you to route !--- traffic via the C links. Note that you need to create duplicate !--- entries for the SS7SUBSYS. Each duplicate entry is !--- associated to a different IOCC that representis each OPC.


prov-add:SS7SUBSYS:NAME="subsys-itp1-itp2",DESC="notSet",SVC="itp-1",
PRI=2,MATEDAPC="itp-2",SSN=0,PROTO="SS7-ANSI",STPSCPIND=0,TRANSPROTO="SCCP"
prov-add:SS7SUBSYS:NAME="subsys-itp2-itp1",DESC="notSet",SVC="itp-2",
PRI=2,MATEDAPC="itp-1",SSN=0,PROTO="SS7-ANSI",STPSCPIND=0,TRANSPROTO="SCCP"
prov-add:SS7SUBSYS:NAME="subsys-itp1-itp2-2",DESC="notSet",SVC="itp-1-opc2",
PRI=2,MATEDAPC="itp-2-opc2",SSN=0,PROTO="SS7-ANSI",STPSCPIND=0,TRANSPROTO="SCCP"
prov-add:SS7SUBSYS:NAME="subsys-itp2-itp1-2",DESC="notSet",SVC="itp-2-opc2",
PRI=2,MATEDAPC="itp-1-opc2",SSN=0,PROTO="SS7-ANSI",STPSCPIND=0,TRANSPROTO="SCCP" 

SLT-1-2651XM#show running-config 
 
.
.
.
service timestamps debug datetime msec
service timestamps log datetime msec
!
hostname SLT-1-2651XM
!
!
memory-size iomem 40
clock timezone PST -8
clock summer-time PDT recurring
ip subnet-zero
!
!
no ip domain lookup
!
!
!
!
controller T1 0/0
 framing esf
 clock source internal
 linecode b8zs
 channel-group 0 timeslots 1 speed 64
 description *** Connected to STP-1 ***
!
controller T1 0/1
 framing esf
 clock source line primary
 linecode b8zs
 cablelength short 133
 channel-group 0 timeslots 1 speed 64
 description *** Connected to STP-2  ***
!
!
interface FastEthernet0/0
 ip address 172.16.20.14 255.255.255.192
 duplex auto
 speed auto
!
interface Serial0/0:0
 no ip address
!
interface Serial0/1:0
 no ip address
 session-set 1
!
ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.20.1
!
!
!


!--- ss7 session 0 and 1 represent the RUDP connections for OPC1. !--- ss7 session 4 and 5 represent the RUDP connections for OPC2. 


ss7 session 0 address 172.16.20.34 7000 172.16.20.14 7000 session-set 0    
ss7 session 1 address 172.16.20.33 7000 172.16.20.14 7000 session-set 0
ss7 session 4 address 172.16.20.34 7002 172.16.20.14 7002 session-set 1
ss7 session 5 address 172.16.20.33 7002 172.16.20.14 7002 session-set 1
.
.
.
!
end