Contents

Introduction

Prerequisites

Requirements

Components Used

Client Limit on a WLC

Configure

Configure the WLC

Verify

Related Information

Introduction

This document describes how to set a limit to the number of clients that can connect to the WLAN in a Cisco Unified Wireless Network (CUWN).

Prerequisites

Requirements

Ensure that you have basic knowledge of the Cisco Unified Wireless Network (CUWN) before you attempt this configuration:

Components Used

The information in this document is based on these software and hardware versions:

- 4400 Wireless LAN Controller (WLC) that runs firmware version 7.0.116.0

- 1131 Lightweight Access Point (LAP)

- 802.11a/b/g Wireless LAN Client Adapters that run software version 4.0

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Client Limit on a WLC

Each of the WLC platforms have an upper limit on the number of WLAN clients that they support. This table shows the upper limit for the various controller platforms:

WLC Platform

Maximum No of Clients

Cisco 2100 Series Controller

350

Cisco 2500 Series Controller

500

Cisco 4400 Series Controller

5000

Cisco 5500 Series Controller

7000

Cisco Flex 7500 Series Controller

20000

WiSM2

10000

To give more control, WLC also provides the option to define the number of clients that connect to each WLAN. This feature is useful in cases where you want to restrict the number of clients (for example, guest clients) that connect to the network, and it also ensure that the WLAN bandwidth is used efficiently in the network.

By default this value is set to 0, which means there is no restriction on the number of clients that can connect to the WLAN.

Note: Currently, you cannot restrict the number of clients that connects to an LAP. Some of the LAPs have limits on clients association. More information on this is available in the Client Association Limits for Lightweight Access Points section of the WLC configuration guide.

The next section describes how to configure the maximum number of clients on a WLAN.

Configure

In this section, you are presented with the information to configure the features described in this document.

In this configuration example, a LAP is registered to a WLC. Two WLANs are configured (LAP1 and LAP2) to which users connect. This example describes how to configure these WLANs in such a way that, at any point, WLAN LAP1 accepts only 25 clients and WLAN LAP2 accepts 50 client associations.

Configure the WLC

This procedure assumes that the WLANs (LAP1 and LAP2) are already configured and describes how to enable the maximum clients feature on these WLANs.

1. From the WLC GUI, click WLANs.

The WLANs page appears. This page lists the WLANs that are configured on the WLC.

2. Click WLAN ID 1 in order to select the WLAN LAP1. The WLANs Edit page appears.

3. Click the Advanced tab.

4. Enter the maximum number of clients allowed in the Maximum Allowed Clients field. This example uses 25 for LAP1.

5. Repeat these steps for WLAN LAP2 and configure the maximum client allowed limit to 50.

Note: To accomplish this configuration through the WLC CLI, use this command: config wlan max-associated-clients max-clients <wlanid>

Verify

You can use the show wlan <wlan id> command to verify the configuration as shown in this sample code:

(Cisco Controller) >show wlan 1

WLAN Identifier.................................. 1

Profile Name..................................... LAP1

Network Name (SSID).............................. LAP1

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Disabled

AAA Policy Override.............................. Disabled

Network Admission Control

Radius-NAC State............................... Disabled

SNMP-NAC State................................. Disabled

Quarantine VLAN................................ 0

Maximum number of Associated Clients............. 25

Number of Active Clients......................... 0

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ vlan50

Multicast Interface.............................. Not Configured

Related Information

- Cisco Wireless LAN Controller Command Reference, Release 7.0.116.0

- Cisco Wireless LAN Controller Configuration Guide, Release 7.0.116.0

- Technical Support & Documentation - Cisco Systems