Objective

The Setup Wizard is a built-in feature that is used to help with the initial configuration of the WAP device. The setup wizard makes it very simple to configure settings. The step-by-step process of the setup wizard guides you through the configuration all the basic settings necessary to run the WAP device.

This article explains how to configure WAP121 and WAP321 device with Setup Wizard.

Applicable Devices | Firmware Version

- WAP121 | 1.0.3.4 (Download latest)

- WAP321 | 1.0.3.4 (Download latest)

Setup Wizard

Step 1. Log in to the Access Point Configuration Utility and choose Run Setup Wizard. The Access Point Setup Wizard window appears:

Step 2. Click Next to continue. The Configure Device - IP Address window appears.

Step 3. Click the radio button that corresponds to the method you want to use to determine the IP address of the WAP.

- Dynamic IP Address (DHCP) (Recommended) - The IP address of the WAP is assigned by a DCHP server.

- Static IP Address - Allows you to create a fixed (static) IP address for the WAP. A static IP address does not change.

Note: If Dynamic IP Address is clicked then, skip to Step 9.

Step 4. Enter the IP address of the WAP in the Static IP Address field. This IP address is created by you and should not be used by another device in the network.

Step 5. Enter the subnet mask of the IP address in the Subnet Mask field.

Step 6. Enter the IP address of the default gateway for the WAP in the Default Gateway field. The default gateway is usually the private IP address assigned to your router.

Step 7. (Optional) If you want to access web pages outside of your network enter the IP address of the primary domain name system (DNS) in the DNS field, the IP address of the DNS server should be given by your Internet service provider (ISP).

Step 8. (Optional) In the Secondary DNS field, enter the IP address of the secondary DNS.

Step 9. Click Next. The Single Point Setup -- Set A Cluster window appears.

Step 10. Click the desired radio button you wish to use. The options are:

- Create a New Cluster – Used to create a new cluster to secure the wireless network as a single entity.

- New Cluster Name - Enter the name of the cluster in the New Cluster Name field.

- AP Location – Enter the location of the AP in the AP Location field.

- Join an Existing Cluster - Used to add a new device to an existing cluster.

- Existing Cluster Name - Enter the name of the cluster that is already created in the Existing Cluster Name field.

- AP Location - Enter the location of the AP in the AP Location field.

- Do not Enable Single Point Setup - Used to disable the cluster setup and configure all the devices individually.

Step 11. Click Next to continue. The Configure Device - Set System Date And Time window appears.

Step 12. Choose a time zone from the Time Zone drop-down list.

Step 13. Click the radio button that corresponds with the method you wish to use to set the time of the WAP.

- Network Time Protocol (NTP) - The WAP gets the time from a NTP server.

- Manually- The time is manually entered into the WAP.

Note: If Manually is clicked then, skip to Step 15.

Step 14. Enter the domain name of the NTP server that provides the date and time in the NTP Server field.

Step 15. If Manually is chosen, then from the System Date drop-down lists, choose the month, day, and year respectively.

Step 16. If Manually is chosen, choose the hour and minutes respectively from the System Time drop-down lists.

Step 17. Click Next. The Enable Security - Set Password window appears.

Step 18. Enter a new password that is required for administrative access on the WAP in the New Password field.

Step 19. Re-enter the same password in the Confirm Password field.

The Password Strength Meter field displays vertical bars that change as you enter the password. The available options are:

- Red - The minimum password complexity requirement is not met.

- Orange - The minimum password complexity requirement is met, but the strength of password is weak.

- Green - The minimum password complexity requirement is met, and the strength of password is strong.

Step 20. (Optional) To enable password complexity, check the Enable check box. This requires that the password is at least 8 characters long and composed of lower and upper case letters and number/symbols.

Step 21. Click Next to continue. The Enable Security - Name Your Wireless Network window appears.

Step 22. Enter the Service Set Identifier (SSID) of the wireless network in the Network Name (SSID) field. The SSID is the name of the wireless local area network.

Step 23. Click Next. The Enable Security - Secure Your Wireless Network window appears.

Step 24. Click the radio button that corresponds with the network security you would like to apply to your wireless network.

- Best Security (WPA2 Personal - AES) - Provides the best security and is recommended if your wireless devices support this option. The WPA2 Personal uses Advanced Encryption Standard (AES)  and a Pre-Shared Key (PSK) among the clients. It uses a new encryption key for each session which makes it difficult to crack.

- Better Security (WPA Personal - TKIP/AES) - Provides security when there are older wireless devices that do not support WPA2. The WPA Personal uses Advanced Encryption Standard (AES) and Temporal Key Integrity Protocol (TKIP). It uses IEEE 802.11i Wi-Fi Standard.

- No Security (Not recommended) - Wireless network does not require a password and can be accessed by anyone.

Note: If No Security is clicked then, skip to step 27.

Step 25. Enter the password for your network in the Security Key field. Adjacent, a strength meter shows the strength of the entered password. Stronger password provides the high security.

Step 26. (Optional) To see the password as you type, check the Show Key as Clear Text check box.

Step 27. Click Next. The Enable Security - Assign The VLAN ID For Your Wireless Network window appears.

Step 28. Enter the VLAN ID for the network in the VLAN ID field. If the management VLAN is same as the VLAN assigned to the wireless network, you can administer the device. You can also use Access Control Lists (ACL) to disable the administration from wireless clients.

Step 29. Click Next. The Summary - Confirm Your Settings window appears.

Step 30. (Optional) If you would like to edit a setting you made, click Back.

Step 31. (Optional) If you would like to exit the Setup Wizard and undo all the changes you made, click Cancel.

Step 32. Review the network settings. Click Submit to enable the settings on the WAP. A loading bar will appear as the WAP enables your settings. When the WAP is finished, the Device Setup Complete window appears.

Step 33. Click Finish to exit the Setup Wizard.