Contents

Introduction

Prerequisites

Requirements

Components Used

Configure

Verify

Troubleshoot

Introduction

This document describes WAN Mode feature on Cisco867VAE Platform and the options that enable the DSL Internet Services.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on  Cisco867VAE Platform.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Configure

Here is the configuration to enable WAN Modes on CISCO867VAE Platform:

Cisco867VAE(config)#wan mode ?

dsl       WAN interface is DSL

ethernet  WAN interface is ethernet

DSL Mode

This mode allows to configure your DSL parameters on ATM or Ethernet but not on any layer 3 interface, that is Gigabitethernet 0 in this device.

Cisco867VAE#sh ip int brief

Interface                  IP-Address      OK? Method Status                Protocol

ATM0                       unassigned      YES NVRAM  administratively down down

Ethernet0                  unassigned      YES NVRAM  administratively down down

FastEthernet0              unassigned      YES unset  up                    up

FastEthernet1              unassigned      YES unset  down                  down

FastEthernet2              unassigned      YES unset  down                  down

FastEthernet3              unassigned      YES unset  down                  down

GigabitEthernet0           unassigned      YES NVRAM  down                  down

Vlan1                      10.106.47.21    YES NVRAM  up                    up

Error messages encountered when in DSL mode:

Cisco867VAE(config)#wan mode dsl

% Ethernet WAN interface will be disabled.

Cisco867VAE(config)#

*Jan 18 04:35:57.931: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down

Cisco867VAE(config)#int gig 0

Cisco867VAE(config-if)#no shut

% WAN interface is DSL

Cisco867VAE(config)#controller vdsl 0

Cisco867VAE(config-controller)#no shut

Cisco867VAE(config)#int eth0

Cisco867VAE(config-if)#no shut

*Jan 18 04:40:46.507: %LINK-3-UPDOWN: Interface Ethernet0, changed state to down

Cisco867VAE(config-if)#int atm 0

Cisco867VAE(config-if)#no shut

*Jan 18 04:40:58.771: %LINK-3-UPDOWN: Interface ATM0, changed state to down

Ethernet Mode

In Ethernet mode you won't be able to configure any DSL parameters, but you can use layer 3 Gigabitethernet interface for outside network.

Cisco867VAE#wan mode ethernet

% DSL interfaces will be disabled.

Cisco867VAE#

*Jan 18 04:12:48.687: %CONTROLLER-5-UPDOWN: Controller VDSL 0, changed state to administratively down

Cisco867VAE(config)#controller vdsl 0

Cisco867VAE(config-controller)#no shut

% Operation not allowed when wan mode is ethernet.

Cisco867VAE#sh ip int brief

Interface                  IP-Address      OK? Method Status                Protocol

ATM0                       unassigned      YES NVRAM  administratively down down

Ethernet0                  unassigned      YES NVRAM  administratively down down

FastEthernet0              unassigned      YES unset  up                    up

FastEthernet1              unassigned      YES unset  down                  down

FastEthernet2              unassigned      YES unset  down                  down

FastEthernet3              unassigned      YES unset  down                  down

GigabitEthernet0           unassigned      YES NVRAM  administratively down down

Vlan1                      10.106.47.21    YES NVRAM  up                    up

Cisco867VAE#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Cisco867VAE(config)#int atm0

Cisco867VAE(config-if)#no shut

% WAN interface is Ethernet.

Cisco867VAE(config-if)#int eth0

Cisco867VAE(config-if)#no shut

% WAN interface is Ethernet.

Cisco867VAE(config)#int gig 0

Cisco867VAE(config-if)#no shut

*Jan 18 04:30:08.851: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down

To disable WAN mode is not possible when it is in DSL mode as its the default mode in CISCO 867 platform.

But when disabled in Ethernet mode, it changes to DSL mode.

Cisco867VAE(config)#no wan mode dsl

Cisco867VAE(config)#do sh run | sec wan

wan mode dsl

Cisco867VAE(config)#do sh run | sec wan

wan mode ethernet

Cisco867VAE(config)#no wan mode ethernet

% Ethernet WAN interface will be disabled.

Note: Use the Command Lookup Tool (registered customers only) in order to obtain more information on the commands used in this section.

Verify

Use this section to confirm that your configuration works properly.

Cisco867VAE#sh run | inc wan mode

wan mode dsl

Troubleshoot

There is currently no specific troubleshooting information available for this configuration.