Contents

Introduction

Prerequisites

Requirements

Components Used

Background Information

Configure

Network Diagram

Configurations

Verify

Redistributed metric

Forward Metric

Related Cisco Support Community Discussions

Introduction

This document describes the Open Shortest Path First Version 3 (OSPFv3) Autonomous System (AS) External Link State Advertisement (LSA) Type 5 route selection mechanism. It presents a network scenario with the configuration for how to select the route received from one Autonomous System Boundary Router (ASBR) over another.

Prerequisites

Requirements

Cisco recommends that you have knowledge of OSPFv3 and IPv6 Routing.

Components Used

This document is not restricted to specific software and hardware versions.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Background Information

If routes are redistributed into OSPFv3 from other IPv6 routing protocols or from IPv6 static routes, these routes becomes OSPF AS-External routes by default. These AS-External routes fall under two categories, external type 1 (O E1) and external type 2 (O E2).

The difference between the two is in the way the cost (metric) of the route is calculated. The cost of a Type 2 route is always the external cost, irrespective of the interior cost to reach that route. The cost of a Type 1 route is the addition of the external cost and the internal cost used to reach that route. A Type 1 route is always preferred over a Type 2 route for the same destination.

Configure

Network Diagram

Consider the below network topology to check the AS-External LSA 5 received on R4 in Area 0 that originated from ASBRs in Area 1. R2 and R3 are Area Border Routers (ABRs).

Configurations

For simplicity, this configuration redistributes the IPv6 static route on ASBRs in Area 1 Router R5 and R1.

R5#

ipv6 route FD00:AAAA:BBBB:CCCC::/64 Null0

!

interface FastEthernet0/0

ipv6 address FD00:AAAA:BBBB:25::5/64

ipv6 ospf 10 area 1

!

ipv6 router ospf 10

router-id 192.168.1.5

redistribute static

R1#

ipv6 route FD00:AAAA:BBBB:CCCC::/64 Null0

!

interface FastEthernet0/1

ipv6 address FD00:AAAA:BBBB:13::1/64

ipv6 ospf 10 area 1

!

ipv6 router ospf 10

router-id 192.168.1.1

redistribute static

Note: If a metric is not specified, OSPFv3 puts a default value of 20 when it redistributes routes from all protocols except Border Gateway Protocol (BGP) routes, which receive a metric of 1.

Verify

You can use these commands in order to verify the redistribution:

R5#show ipv6 ospf

Routing Process "ospfv3 10" with ID 192.168.1.5

Event-log enabled, Maximum number of events: 1000, Mode: cyclic

It is an autonomous system boundary router

Redistributing External Routes from,

static

Router is not originating router-LSAs with maximum metric

Initial SPF schedule delay 5000 msecs

Minimum hold time between two consecutive SPFs 10000 msecs

Maximum wait time between two consecutive SPFs 10000 msecs

Minimum LSA interval 5 secs

Minimum LSA arrival 1000 msecs

LSA group pacing timer 240 secs

Interface flood pacing timer 33 msecs

Retransmission pacing timer 66 msecs

Number of external LSA 2. Checksum Sum 0x0100D4

Number of areas in this router is 1. 1 normal 0 stub 0 nssa

Graceful restart helper support enabled

Reference bandwidth unit is 100 mbps

RFC1583 compatibility enabled

Area 1

Number of interfaces in this area is 1

SPF algorithm executed 5 times

Number of LSA 16. Checksum Sum 0x08011B

Number of DCbitless LSA 0

Number of indication LSA 0

Number of DoNotAge LSA 0

Flood list length 0

R1#show ipv6 ospf

Routing Process "ospfv3 10" with ID 192.168.1.1

Event-log enabled, Maximum number of events: 1000, Mode: cyclic

It is an autonomous system boundary router

Redistributing External Routes from,

static

Router is not originating router-LSAs with maximum metric

Initial SPF schedule delay 5000 msecs

Minimum hold time between two consecutive SPFs 10000 msecs

Maximum wait time between two consecutive SPFs 10000 msecs

Minimum LSA interval 5 secs

Minimum LSA arrival 1000 msecs

LSA group pacing timer 240 secs

Interface flood pacing timer 33 msecs

Retransmission pacing timer 66 msecs

Number of external LSA 2. Checksum Sum 0x0100D4

Number of areas in this router is 1. 1 normal 0 stub 0 nssa

Graceful restart helper support enabled

Reference bandwidth unit is 100 mbps

RFC1583 compatibility enabled

Area 1

Number of interfaces in this area is 1

SPF algorithm executed 6 times

Number of LSA 16. Checksum Sum 0x08AD19

Number of DCbitless LSA 0

Number of indication LSA 0

Number of DoNotAge LSA 0

Flood list length 0

So, both the ASBR Routers, R5 and R1 redistribute the IPv6 static routes. In order to check the redistributed route in Routing Table and OSPFv3 Database on Router R4 for prefix FD00:AAAA:BBBB:CCCC::/64, enter this command:

Redistributed metric

As mentioned earlier, the metric value is set by default to 20 when the routes are redistributed into OSPFv3. Next, define the value 10 while you redistribute on ASBR 192.168.1.1 (R1) and check the output on Router 4.

Here are the changes implemented on R1:

R1(config)#ipv6 router ospf 10

R1(config-rtr)#redistribute static metric 10

The Routing Table now shows only  one entry in the IPv6 Routing Table. Check the OSPF database further for this AS-External LSA:

Forward Metric

The Forward Metric is the cost to reach ASBR from the router. This can be checked with these commands:

R4#show ipv6 ospf border-routers

OSPFv3 Router with ID (192.168.1.4) (Process ID 10)

Codes: i - Intra-area route, I - Inter-area route

I 192.168.1.1 [3] via FE80::C801:37FF:FE2C:6, FastEthernet0/0, ASBR, Area 0, SPF 2

I 192.168.1.1 [2] via FE80::C802:BFF:FEB4:6, FastEthernet0/1, ASBR, Area 0, SPF 2

i 192.168.1.3 [1] via FE80::C802:BFF:FEB4:6, FastEthernet0/1, ABR, Area 0, SPF 2

i 192.168.1.2 [1] via FE80::C801:37FF:FE2C:6, FastEthernet0/0, ABR, Area 0, SPF 2

I 192.168.1.5 [2] via FE80::C801:37FF:FE2C:6, FastEthernet0/0, ASBR, Area 0, SPF 2

In this output, the cost to reach ASBRs (R1 and R5) is 2 from Router R4. By default, the cost for FastEthernet Interface in OSPFv3 is 1. So in this case, the cost is 2 from R4 to reach R1 or R5: Forward Metric = Router cost to reach ABR (1) + ABR cost to reach the ASBR (1) = 2.

Change the redistribution metric to 10 on R5 as well, so both of the routes are installed again in the IPv6 Routing Table.

Here are the changes implemented on R5:

R5(config)#ipv6 router ospf 10

R5(config-rtr)#redistribute static metric 10

The IPv6 Routing Table and OSPFv3 RIB on R4 shows:

R4#sh ipv6 ospf rib detail

* FD00:AAAA:BBBB:CCCC::/64, Ext-2, cost 10/2

source 192.168.1.1, tag 0

via FE80::C801:37FF:FE2C:6, FastEthernet0/0

via FE80::C802:BFF:FEB4:6, FastEthernet0/1

LSA: 4005/0/192.168.1.5

LSA: 4005/0/192.168.1.1

R4#show ipv6 route FD00:AAAA:BBBB:CCCC::/64

Routing entry for FD00:AAAA:BBBB:CCCC::/64

Known via "ospf 10", distance 110, metric 10, type extern 2

Route count is 2/2, share count 0

Routing paths:

FE80::C802:BFF:FEB4:6, FastEthernet0/1

Last updated 00:09:49 ago

FE80::C801:37FF:FE2C:6, FastEthernet0/0

Last updated 00:00:14 ago

Now lets change the cost to reach one of the ASBRs but with same redistribution metric and check the same output.

Increase the OSPFv3 Cost on fa0/1 for Router R4:

R4(config)#int fa0/1

R4(config-if)#ipv6 ospf cost 10

Check the Forward Metric. It shows that now the cost to reach ASBR R1 is 11 from Fa0/1 Interface:

R4#show ipv6 ospf border-routers

OSPFv3 Router with ID (192.168.1.4) (Process ID 10)

Codes: i - Intra-area route, I - Inter-area route

I 192.168.1.1 [3] via FE80::C801:37FF:FE2C:6, FastEthernet0/0, ASBR, Area 0, SPF 3

I 192.168.1.1 [11] via FE80::C802:BFF:FEB4:6, FastEthernet0/1, ASBR, Area 0, SPF 3

i 192.168.1.3 [10] via FE80::C802:BFF:FEB4:6, FastEthernet0/1, ABR, Area 0, SPF 3

i 192.168.1.2 [1] via FE80::C801:37FF:FE2C:6, FastEthernet0/0, ABR, Area 0, SPF 3

I 192.168.1.5 [2] via FE80::C801:37FF:FE2C:6, FastEthernet0/0, ASBR, Area 0, SPF 3

Now the IPv6 Routing Table and OSPFv3 RIB on R4 shows:

R4#sh ipv6 ospf rib detail

* FD00:AAAA:BBBB:CCCC::/64, Ext-2, cost 10/2

source 192.168.1.5, tag 0

via FE80::C801:37FF:FE2C:6, FastEthernet0/0

LSA: 4005/0/192.168.1.5

LSA: 4005/0/192.168.1.1

R4#show ipv6 route FD00:AAAA:BBBB:CCCC::/64

Routing entry for FD00:AAAA:BBBB:CCCC::/64

Known via "ospf 10", distance 110, metric 10, type extern 2

Route count is 1/1, share count 0

Routing paths:

FE80::C801:37FF:FE2C:6, FastEthernet0/0

Last updated 00:02:19 ago

So the route with the lower Forward Metric is installed in the IPv6 Routing Table.

In summary, when you have multiple entries for AS-External LSA, the first preference is given to the metric (Redistributed metric). The route with the lower metric is installed in the IPv6 Routing Table. The second preference is given to the Forward Metric, if the redistributed metric is same. The route with the lower Forward Metric is installed in the IPv6 Routing Table.